Management, Message, Action | Vixel 335 specs

Message

Vixel Model 335 Installation & Configuration Guide	CHAPTER 3 Management

Note: To cancel out of the file transfer facility, press CTRL+X several times.

d.Type the following and press Enter. quit

4.In the terminal session window, type 1 to verify and store the new firmware. The following message appears.

Clearing backup host filename.. Clearing backup host IP address.. Verifying file integrity.. Erasing flash memory.. Programming flash memory.. Verifying..

*PROGRAM LOAD SUCCESSFUL*

Type fw, then type 1.

The active and alternate firmware versions are displayed.

5.If the “alternate version” is anything other than the firmware you just downloaded, verify that the file is good and repeat the download.

6.If you want to activate the alternate version (the newly downloaded firmware):

a.Type 2 to select the alternate version for execution on the next boot cycle.

b.Type 1 to verify that the following message is displayed under the firmware versions: “Note: ALTERNATE selected for execution on next boot cycle.” (If this message is not displayed, repeat steps a and b to toggle back.)

c.Type 5 to reboot.

The management agent disconnects, reboots, and activates the downloaded firmware. The “Disconnecting and Rebooting” message appears.

The firmware is downloaded.

Serial Method (Menu Option 4)

The Serial method for downloading firmware is available for Windows only.

1.Ensure that the switch and workstation are connected through a serial null modem cable.

2.Type 4.

The file transfer facility appears.

3.Choose Send File from the Transfer pull-down menu in HyperTerminal. The Send File dialog box appears.

4.Type (or browse for) the filename, select “1K Xmodem” from the Protocol drop- down list, and click Send.

A status message appears.

5.If the status message says anything other than “File transfer completed,” perform the action recommended for the appropriate message shown below.

Message	Action

CRC Error	Try another file. The file you are attempting to download may be corrupted.

Time out error	Cycle power to the switch and retry the download procedure.

Access denied	Close and reestablish the connection. Cycle power to the switch and retry the
	download procedure.

40

Image 43

Vixel manual Management, Vixel Model 335 Installation & Configuration Guide, Message, Action

Contents

guide Managed Storage SwitchINSTALLATION&CONFIGURATION InSpeed Model Part Number 00041363-001 Rev. A A p p e n d i x e s Table of Contents Overview FeaturesCHAPTER 1 Introduction About This Guide CHAPTER 1 Introduction Fibre Channel - Arbitrated LoopInSpeed Technology Vixel Model 335 Installation & Configuration Guide Unpacking the Switch CHAPTER 2 InstallationInstalling the Switch CHAPTER 2 Installation Using Small Form - Factor Pluggable SFP TransceiversPerforming a Power On Systems Test Small Form-Factor Pluggable SFP Installation Attaching Devices Setting Up the Switch System LEDs Understanding the Switch’s LEDsPower On Figure 2-1. Switch features diagram Port LEDs CHAPTER 2 InstallationSystem LEDs Indication Activity PortBypassed Status Zone Zone Zone Cascading SwitchesFigure 2-4. Cascading Switches in Overlapping Zones Cascading with Non-Overlapping Zones Figure 2-7. ACCEPTABLE Single Cascade in Zones 2-12 Only CHAPTER 3 Management Using the Web ManagerO v e rv i e w Connecting to the Web Manager Figure 3-1. Web Manager Home Page CHAPTER 3 ManagementNavigation Logging On and Off Location in Web Manager Configuring the SwitchConfiguration Task Resetting the Switch Figure 3-2. System Information Page System Information SettingsSetting Description Figure 3-3. System Information Change Settings Page Network Settings Blocking ARB Switch SpeedSwitching Mode Switch Identification Figure 3-4. Time Information Page Downloading the Switch ConfigurationTime Settings Figure 3-5. Time Information Change Settings Page Figure 3-6. Firmware Information Page Firmware Settings Figure 3-7. Event Log Messages Page 1. Click Change Firmware SettingsEvent Log Messages 1. Click Load New Firmware Image Figure 3-8. FC Switch Information Page FC Switch InformationFigure 3-9. FC Switch Information Page with Highlighted Zones Figure 3-10. Ordered Set Information Page OS InformationDetection Indication RRDY Figure 3-11. Ordered Set Information Page with Highlighted Zones Port Usage InformationFigure 3-12. Received Port Utilization Page Value Figure 3-14. Received Port Utilization Change Settings PageFigure 3-13. Received Port Utilization Page with Highlighted Zones Figure 3-15. Port Information Page Port Settings Figure 3-17. Port Information Page with Transceiver Information Figure 3-16. Port Information Page with Highlighted Zones Figure 3-18. Cascade Information Page Mode Figure 3-19. Cascade Information Page with Highlighted Zones Switch Policy Policy SettingsFigure 3-20. Policies Page Figure 3-21. Policies Change Settings Page To update the switch’s policies Figure 3-24. Zone Information Page Zone SettingsFigure 3-22. Overlapping Zones Figure 3-23. Non-overlapping Zones Figure 3-25. Overlapping Zone 1 Information Page Overlapping Zones Non-Overlapping Zones Figure 3-26. Overlapping Zone 1 Information Configuration Page always in Zone Figure 3-28. Non-Overlapping Zones Information Configuration PageFigure 3-27. Non-Overlapping Zone Information Page Note Ports 11 and 12 are Highlighted Zones Connecting to the CLI Using the Command Line Interface CLI CLI Command Configuring Switch Information Changing the Switch’s IP ParametersEnabling or Disabling DHCP Requests tftp IPaddress Managing the FirmwareDownloading New Firmware tftp -i IPaddress PUT filename ramdisk Action Message Configuring the Trap Destination Table Option Viewing Management, Policy, and Threshold Settings Changing the CLI/Web Password Policy Policies Threshold Information Settings Actions Options 2-Emergency, 3-Alert, 4-Critical, 5-Error, 6-Warning Command Changing the Switching Mode Description Displaying Ports Description Viewing the Event Log Resetting the SwitchResetting the Hardware Resetting the Switch to Factory Default Settings Overlapping Zoning Configuration Changing the Switch’s Operating SpeedViewing and Understanding Zoning Information Example noz 25,6,7,8 39,10 Non-Overlapping Zoning Configuration Technical Support ReferenceCHAPTER 4 Technical If the Mgmt Present LED continues to blink and POST has already Tro ub l e sh oo ti n gIf the switch’s Fault LED remains lit, the switch requires repair CHAPTER 4 Technical Reference Recommended Action Fibre Channel ReferencesSmall Form-Factor Pluggable SFP Issues Problem Appendixes S p e c i f i c a t i o n s APPENDIX A Specifications Requirement Operating ConditionsAPPENDIX A Specifications Vixel Model 335 Operating Conditions General Commands CommandsConsole Commands Command Action Commands APPENDIX B CLI Console Commands Syntax Action APPENDIX C Event MessagesEvent Meaning APPENDIX C Event Messages Meaning Vixel Model 335 Installation & Configuration GuideAPPENDIX C Event Messages Event Meaning Arbitrated Loop Physical Addresses Cross ReferencesLoop ID-ALPA APPENDIX D APPENDIX E Glossary Enables the switch to be divided into separate environments Index Index