| TorqueMaster® Spring |
|
|
| Removal continued... |
|
|
Tools Needed: | (Spring Tube should be free to rotate in |
|
|
| either direction.) If the counterbalance |
|
|
Recommended | cable is still taut and the TorqueMaster® |
|
|
Spring Tube is difficult to rotate, that is an |
|
| |
tools from |
|
| |
indication that spring tension still exists |
|
| |
page 5 |
|
| |
on the left hand spring. Repeat Steps 1 |
|
| |
| and 2 for releasing spring tension on the |
|
|
| left hand side. | remove top |
|
| Step 4: Using a flat tip screwdriver, pry | lag screw |
|
| the counter gear and counter cover | Fig. 5 | |
| from the right hand end bracket (Fig. 4 |
|
|
| on previous page). Discard the counter |
|
|
| gear and counter cover. On double spring |
| use locking pliers |
| applications, repeat for left hand side. |
| |
|
| to hold end bracket | |
|
|
| |
| Step 5: Remove the upper 5/16” x |
|
|
|
|
| |
| bracket (Fig. 5). Attach locking pliers to |
| remove #10 |
| the upper portion of the end bracket and |
| phillips head |
| hold the housing steady while removing |
| screw |
| the lower 5/16” x |
|
|
| #10 x 1/2” phillips head screw from the |
|
|
| end bracket (Fig. 6). |
|
|
| Step 6: Holding the right hand end |
|
|
| bracket steady with locking pliers, | remove |
|
| carefully pry the end bracket and drive | bottom lag |
|
| gear off the winding shaft using a flat tip | screw | Fig. 6 |
| screwdriver (Fig. 7). |
| |
| CAUTION: THE WINDING SHAFT MAY |
| hold the |
| ROTATE WHEN REMOVING THE END |
| end bracket |
| BRACKET AND DRIVE GEAR. |
| steady with |
| Step 7: Repeat Step 4 for the left hand |
| locking pliers |
|
|
| |
| side. Holding the left hand end bracket |
|
|
| steady with locking pliers, carefully pry |
|
|
| the end bracket off the winding shaft |
|
|
| using a flat tip screwdriver (Fig. 7). |
|
|
| Step 8: Remove the two (2) lag bolts |
| pry end bracket from winding |
| attaching the center bracket assembly to |
| |
|
| shaft using a flat tip screw | |
| the header board (Fig. 8). |
| |
|
| driver and locking pliers | |
|
|
| |
| Step 9: Lift the right hand side of the |
|
|
| TorqueMaster® Spring Tube and slide the |
|
|
| cable drum off. Realign the groove in the |
|
|
| winding shaft with the round notch in the | Fig. 7 | |
| flagangle and drape the counterbalance | CENTER |
|
| cable with drum over the flagangle. Lift | remove cable drum and | |
| BRACKET | ||
| the left hand side of the TorqueMaster® | ASSEMBLY | winding shaft |
| Spring Tube and slide the cable drum |
|
|
| and winding shaft off (Fig. 9). Drape the |
|
|
| counterbalance cable with drum over the |
|
|
| flagangle. Lift the TorqueMaster® spring |
|
|
| assembly off the flagangles and out of |
|
|
| the doorway. Unhook the counterbalance |
|
|
| cables from the bottom brackets and |
|
|
| remove all parts from the work area. |
| lift |
| NOTE: The cable drums may be difficult to |
| |
|
| TorqueMaster® | |
| remove. If so, twist the cable drum to aid |
| Spring Tube |
| in removal. | (2) 5/16” x | off flagangle |
| NOTE: Continue with “P4” on page 9 after | drape cable across | |
| hex head lag | top of flagangle | |
| completing this step. | screws |
|
|
| Fig. 8 | Fig. 9 |
8
Please Do Not Return This Product To The Store. Contact your local
local yellow pages/business listings or go to the Find a Dealer section online at