Wayne-Dalton 8850 installation instructions Top Bracket, Lift Handle

7	Top Bracket
Tools Needed:	Align upper-center hole of top bracket
	with vertical groove on the end stile and
Power Drill	ensure top bracket is level and aligned
	with edge of top section. Secure with
7/16” Socket	(4) 1/4”- 20 x 7/8” self drilling screws,
	one in each corner of the top bracket, as
Driver
	shown. Loosely fasten top bracket slide
	with (1) 5/16” - 18 x 3/4” carriage bolt
	and 5/16” - 18 hex nut. Insert roller into
	slide. Repeat for other side.
	If your door has double end stiles then it
	will require 4 top brackets; as shown, in
	which case an additional top bracket will
	be installed in the same manner next to
	the first top bracket with one roller being
	placed through both top bracket slides.
	Four reinforcement brackets will then be
	installed under the 4 top brackets and
	secured to the section with (4) 1/4”- 20 X

top bracket	top section
base

(4) 1/4”- 20 x 7/8” self drilling screws

end stile

	(1) 5/16” - 18 x 3/4”
		carriage bolt
	top	top section
	bracket
	slide
5/16” - 18	top
	bracket
hex nut
	base

7/8” self drilling screws.

NOTE: If your door is trolley operated; it

is recommended that an optional strut be

installed on the top rail.

Now stack the top section. Take care to

ensure it is aligned properly with the other

sections.

top section

(16)1/4”- 20 x 7/8” self drilling

screws

(4) 1/4”- 20 x 7/8”

self drilling

screws

(4)Reinforcement Brackets

8	Lift Handle		Lock
			Section
Tools Needed:	Bottom section		Lift
	Locate the center most stile of the bottom section of the door.		handle
Tape Measure	On the inside of the door, center the lift handle vertically with				Lock
	the center stile; horizontally on the bottom section rail, and
					Section
	within 8” of the bottom of the section.
Pencil
	Use the lift handle as a template, place a mark at each hole
	location onto the bottom section rail. Drill a 9/32” diameter		(2) 1/4” - 20	Lift
Power Drill	hole through the section at each marked location.
			x 5/8” self
				handle
	NOTE: Be extremely careful to keep drill straight.		drilling screws
9/32” Drill Bit	Assemble the outside and inside lift handle to the section	bottom			bottom
	using (4) 1/4” -20 x 5/8” self drilling screws.	Section			Section
1/4” Wrench	Lock (2nd) section		lift handle outside
	Position the lift handle’s bottom hole 4” from the bottom of				Lock
	the lock (2nd) section. Vertically align with the lift handle on		Lock
					Section
	the bottom section. Using the lift handle as a template, place		Section
	mark at each hole location onto the center stile. Drill a 9/32”		(2) 1/4” - 20
	diameter through the section at each marked location.
	NOTE: Be extremely careful to keep drill straight.		x 5/8” self
	Assemble the outside and inside lift handle to the section		drilling
			screws
	using (4) 1/4” -20 x 5/8” self drilling screws.	Lift		Lift
	WARNING			handle
		handle
	TO AVOID POSSIBLE INJURY, LIFT HANDLES THAT ARE
	INSTALLED WITHIN 4 INCHES OF A SECTION INTERFACE
	SHALL PROMOTE VERTICAL ORIENTATION OF THE HAND.				bottom
			bottom Section		Section
			lift handle inside
12					12

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com