Contents | Woodstock W1762, W1761 manual

Contents

INTRODUCTION

INTRODUCTION	2
Woodstock Technical Support	2
W1761 Specifications	3
W1762 Specifications	4
Controls and Features	5
SAFETY	6
Standard Safety Instructions	6
Additional Safety for Table Saws	8
Preventing Kickback	9
Protecting Yourself from Kickback	10
Common Terms	11
ELECTRICAL	12
W1761 220V Single-Phase Operation	12
Extension Cords	12
W1761 Electrical Specifications	12
W1762 220V 3-Phase Operation	13
W1762 440V 3-Phase Operation	13
Phase Converter	13
Electrical Specifications	13
Rewiring to 440V	13
SETUP	14
Unpacking	14
Items Needed for Set Up	14
Inventory	15
Cleaning Machine	17
Machine Placement	17
Extension Table	18
Saw Blade	21
Arbor	21
Table Insert	22
Blade Guard & Splitter	22
Riving Knife	23
ON/OFF Switch	24
Miter Gauge	24
Fence Components	24
Dust Collection	25
Recommended Adjustments	25
Test Run	26

OPERATIONS	27
General	27
Basic Controls	27
Disabling On/Off Switch	28
Blade Selection	28
Workpiece Inspection	30
Non-Through & Through Cuts	30
Ripping	31
Crosscutting	32
Miter Cuts	33
Blade Tilt & Bevel Cuts	33
Dado Cutting	34
Rabbet Cutting	36
Resawing	38
Table Saw Accessories	41
MAINTENANCE	44
General	44
Cleaning	44
Lubrication	44
SERVICE	45
Troubleshooting	45
Replacing Flat Belt	47
Blade Tilt Stops	49
Digital Readout	50
Miter Slot to Blade Parallelism	51
Blade Alignment	52
Adjusting Fence	53
Miter Gauge	54
W1761/W1762 Electrical Components	55
W1761 Wiring Diagram	56
W1762 Electrical Components	57
W1762 Wiring Diagram 220V, 3-Phase	58
W1762 Wiring Diagram 440V, 3-Phase	59
PARTS	60
Blade Guard Assembly	60
Fence Assembly	61
Miter Gauge Assembly	62
Main Table, Motor & Cabinet	63
Extension Table Assembly	66
Label Placement	67

SAFETY ELECTRICAL

SET UP OPERATIONS MAINTENANCE SERVICE

USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!

PARTS

Image 15

Woodstock W1762, W1761 owner manual Contents

Contents

Table SAW with Riving Knife Inventory Differences Important Changes to Assembly Blade Installation Blade RequirementsBlade Size Requirements Blade Guard GuardSpreader Location to secure blade guard Screw Installing Blade Guard & Spreader To remove the pawls, do these steps Anti-Kickback Pawls When Not to Use the Blade Guard When to Use the Blade Guard Riving Knife Installing Riving KnifeWhen to Use the Riving Knife When Not to Use the Riving Knife Spreader or Riving Knife Alignment Checking AlignmentTools Needed Follow Checking Alignment, Steps 1-4, on Adjusting AlignmentAdjusting Bent Spreader/Riving Knife Possible Tools Needed D3697-Standard Zero-Clearance Insert Optional Table Insert Description New Parts =\FjVainBVXcZhVcYIddah Page Contents Woodstock Technical Support Introduction Introduction Introduction Controls and Features Standard Safety Instructions Safety Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Table Saws Below are tips to avoid the most common causes of kickback Preventing Kickback Protecting Yourself from Kickback Do not stand directly behind Blade when making a cut Common Terms W1761 220V Single-Phase Operation W1761 Electrical SpecificationsExtension Cords Electrical Specifications W1762 220V 3-Phase OperationW1762 440V 3-Phase Operation Phase Converter Immediately discard all Plastic bags and pack Items Needed for Set UpUnpacking Description Qty Box Inventory Figure InventoryMachine Inventory Fence Inventory Extension Table Inventory Fence Rail Inventory Machine Placement Cleaning Machine Extension Table To install the front and rear rails, do these steps Leveling main extension table Support Leg Hex Nut Foot Support leg fastened to main Extension table To change the arbor, do these steps To install the blade, do these stepsSaw Blade Arbor Blade Guard & Splitter To install and adjust the table insert, do these stepsTo install the blade guard, do these steps Table Insert Splitter To install the riving knife, do these steps Miter Gauge ON/OFF SwitchTo install the switch, do these steps To install the miter gauge, do these steps Recommended CFM at Dust Port Recommended AdjustmentsRecommended adjustment checklist Dust Collection To test run the machine, do these steps Test Run Basic Controls General Blade Selection Disabling On/Off SwitchRipping blade features see Figure Crosscut blade features see Figure Combination blade features see Figure Laminate blade features see FigureDado Blades see Figure Through Cuts Workpiece InspectionNon-Through Through Cuts Non-Through Cuts Typical ripping operation Ripping Crosscutting To make a crosscut using the miter gauge, do these steps Miter Cuts Blade Tilt & Bevel CutsTo perform a miter cut, do these steps To use a stacked or wobble dado blade, do these steps Dado Cutting Disconnect the SAW from Power To cut rabbets with the dado blade, do these steps Rabbet Cutting First cut to create a rabbet With a standard blade To cut rabbets with the standard blade, do these steps Resaw Barrier Resawing To build the auxiliary fence, do these steps Auxiliary Fence To perform resawing operations, do these steps Resawing Operations Table Saw Accessories D3585 Bore General Purpose D3586 Fine Finishing D3587 100 Operations Weekly Check CleaningLubrication Daily Check Motor & Electrical Troubleshooting W1761/W1762 12 Table Saw with Riving Knife Operations To remove the flat belt, do these steps Replacing Flat Belt Deflect it no more than 1⁄8 To install the new belt, do these steps Blade Tilt Stops To set the 90 stop bolt, do these stepsTo set the 45 stop bolt, do these steps To adjust the tilt indicator arrow, do these steps Digital ReadoutTo set the digital readout, do these steps Miter Slot to Blade Parallelism Example of adjusting blade to Miter slot Blade Alignment To adjust the blade by moving the table, do these steps Adjusting Fence Square and HeightClamping Pressure and Parallelism Miter gauge diagram W1761 magnetic switch Switch See Figure W1761 Wiring Diagram W1762 Electrical Components W1762 magnetic switch prewired to 220V, 3-phase W1762 Wiring Diagram 220V, 3-Phase W1762 Wiring Diagram 440V, 3-Phase Parts Blade Guard Assembly Blade Guard Assembly Parts List Fence Assembly Fence Assembly Parts List Miter Gauge Assembly Miter Gauge Parts List Main Table, Motor & Cabinet Motoraccesscover Main Table, Motor & Cabinet Parts List Mitergaugemountingbracket Extension Table Assembly Extension Table Parts List Label Placement Warranty Page Page Comments Warranty Registration BOX BELLINGHAM, WA