Miter Gauge Assembly Miter Gauge Parts List | Woodstock W1761

W1761/W1762 12" Table Saw with Riving Knife

Miter Gauge Assembly

��

	��		��
			��
��	��
	��		��
��	��
��			��
��
��			��
��
��			��
��
		��	��
			��
	��
	��

Miter Gauge Parts List

REF	PART�#	DESCRIPTION
200	X1761200	MITER�GAUGE�ASSEMBLY
201	XPS06	PHLP�HD�SCR�10-24�X�3/8
202	X1761202	POINTER
203	X1761203	BLOCK
204	X1761204	SHAFT
205	X1761205	MITER�GAUGE�SCALE
206	XPS25	PHLP�HD�SCR�8-32�X�5/8
207	XPN14	HEX�NUT�8-32
208	XPS04	PHLP�HD�SCR�1/4-20�X�1/2

REF	PART�#	DESCRIPTION
209	XPSS53M	SET�SCREW�M5-.8�X�12
210	X1761210	MITER�GAUGE�HANDLE
211	XPW01M	FLAT�WASHER�8MM
212	X1761212	MITER�GAUGE
213	X1761213	PLATE
214	X1761214	GUIDE�PLATE
215	XPFH9M	FLAT�HD�SCR�M6-1�X�6
216	XPORKS003	O-RING�4.75�X�1.7�KS-3

PARTS

-62-

Image 76

Woodstock W1761, W1762 owner manual Miter Gauge Assembly Miter Gauge Parts List

Contents

Table SAW with Riving Knife Important Changes to Assembly Inventory Differences Blade Requirements Blade InstallationBlade Size Requirements Guard Blade GuardSpreader Installing Blade Guard & Spreader Location to secure blade guard Screw Anti-Kickback Pawls To remove the pawls, do these steps When to Use the Blade Guard When Not to Use the Blade Guard Installing Riving Knife When to Use the Riving KnifeWhen Not to Use the Riving Knife Riving Knife Checking Alignment Spreader or Riving Knife AlignmentTools Needed Adjusting Alignment Adjusting Bent Spreader/Riving KnifePossible Tools Needed Follow Checking Alignment, Steps 1-4, on Optional Table Insert D3697-Standard Zero-Clearance Insert New Parts Description =\FjVainBVXcZhVcYIddah Page Contents Introduction Woodstock Technical Support Introduction Introduction Controls and Features Safety Standard Safety Instructions Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Table Saws Preventing Kickback Below are tips to avoid the most common causes of kickback Do not stand directly behind Blade when making a cut Protecting Yourself from Kickback Common Terms W1761 Electrical Specifications W1761 220V Single-Phase OperationExtension Cords W1762 220V 3-Phase Operation W1762 440V 3-Phase OperationPhase Converter Electrical Specifications Items Needed for Set Up UnpackingDescription Qty Immediately discard all Plastic bags and pack Inventory Machine InventoryFence Inventory Box Inventory Figure Fence Rail Inventory Extension Table Inventory Cleaning Machine Machine Placement To install the front and rear rails, do these steps Extension Table Leveling main extension table Support Leg Hex Nut Foot Support leg fastened to main Extension table To install the blade, do these steps Saw BladeArbor To change the arbor, do these steps To install and adjust the table insert, do these steps To install the blade guard, do these stepsTable Insert Blade Guard & Splitter To install the riving knife, do these steps Splitter ON/OFF Switch To install the switch, do these stepsTo install the miter gauge, do these steps Miter Gauge Recommended Adjustments Recommended adjustment checklistDust Collection Recommended CFM at Dust Port Test Run To test run the machine, do these steps General Basic Controls Disabling On/Off Switch Ripping blade features see FigureCrosscut blade features see Figure Blade Selection Laminate blade features see Figure Combination blade features see FigureDado Blades see Figure Workpiece Inspection Non-Through Through CutsNon-Through Cuts Through Cuts Ripping Typical ripping operation To make a crosscut using the miter gauge, do these steps Crosscutting Blade Tilt & Bevel Cuts Miter CutsTo perform a miter cut, do these steps Dado Cutting To use a stacked or wobble dado blade, do these steps Disconnect the SAW from Power Rabbet Cutting To cut rabbets with the dado blade, do these steps To cut rabbets with the standard blade, do these steps First cut to create a rabbet With a standard blade Resawing Resaw Barrier Auxiliary Fence To build the auxiliary fence, do these steps Resawing Operations To perform resawing operations, do these steps Table Saw Accessories D3585 Bore General Purpose D3586 Fine Finishing D3587 100 Operations Cleaning LubricationDaily Check Weekly Check Troubleshooting Motor & Electrical Operations W1761/W1762 12 Table Saw with Riving Knife Replacing Flat Belt To remove the flat belt, do these steps To install the new belt, do these steps Deflect it no more than 1⁄8 To set the 90 stop bolt, do these steps Blade Tilt StopsTo set the 45 stop bolt, do these steps Digital Readout To adjust the tilt indicator arrow, do these stepsTo set the digital readout, do these steps Example of adjusting blade to Miter slot Miter Slot to Blade Parallelism To adjust the blade by moving the table, do these steps Blade Alignment Square and Height Adjusting FenceClamping Pressure and Parallelism Miter gauge diagram Switch W1761 magnetic switch W1761 Wiring Diagram See Figure W1762 magnetic switch prewired to 220V, 3-phase W1762 Electrical Components W1762 Wiring Diagram 220V, 3-Phase W1762 Wiring Diagram 440V, 3-Phase Blade Guard Assembly Blade Guard Assembly Parts List Parts Fence Assembly Fence Assembly Parts List Miter Gauge Assembly Miter Gauge Parts List Main Table, Motor & Cabinet Main Table, Motor & Cabinet Parts List Motoraccesscover Mitergaugemountingbracket Extension Table Assembly Extension Table Parts List Label Placement Warranty Page Page Warranty Registration Comments BOX BELLINGHAM, WA