Fence Rail Inventory, Extension Table Inventory | Woodstock W1761

W1761/W1762 12" Table Saw with Riving Knife

Fence Rail Inventory

SET UP

Box Inventory: (Figure 11)		Qty
A.	Fence Tube (93" Long)	1
B.	Rear Rail (79" Long)	1
C.	Front Rail (93" Long)	1
Extension Table Inventory
Box Inventory: (Figure 12)		Qty
A.	Extension Table	1
B.	Lower Shelf	1
C.	Shelf End Plate	1
D.	Support Legs	2
E.	Lower Shelf Brackets	2
Tools and Hardware (Not Shown):		Qty
•	Cap Screws M8-1.25 x 25
	(Rear Rail/Table/Ext. Table)	8
•	Lock Washers 8mm
	(Rear Rail/Table/Ext. Table)	10

•Flat Head Screws M8-1.25 x 25

	(Front Rail/Table/Ext. Table)	8
•	Flat Washers 8mm
	(Front Rail/Ext. Table/Rear Rail)	14
•	Hex Nuts M8-1.25
	(Front Rail/Ext. Table/Rear Rail)	8
•	Hex Nuts M6-1
	(Brackets/Shelf End Plate)	2
• Hex Bolts M6-1 x 12		4
	(Cabinet/Lower Shelf Brackets/Shelf End Plate)
• Phillip Head Screws M6-1 x 12
	(Ext. Table/Legs/End Plate)	12
•	Flat Washers 6mm
	(Ext. Table/Legs/End Plate)	16
• Feet 3/8"-16 x 2 (Legs)		2
• Hex Nuts 3/8-16 (Feet)		2
• Flat Washers 10mm (Cabinet)		2
• Hex Bolts M10-1.5 x 25 (Cabinet)		2
• Flange Bolts M8-1.25 x 12
	(Tube/Front Rail)	9

A

CB

Figure 11. Fence rail components.

A

B

E

D

C

Figure 12. Extension table components.

-16-

Image 30

Woodstock W1761, W1762 owner manual Fence Rail Inventory, Extension Table Inventory

Contents

Table SAW with Riving Knife Important Changes to Assembly Inventory Differences Blade Installation Blade RequirementsBlade Size Requirements Blade Guard GuardSpreader Installing Blade Guard & Spreader Location to secure blade guard Screw Anti-Kickback Pawls To remove the pawls, do these steps When to Use the Blade Guard When Not to Use the Blade Guard When Not to Use the Riving Knife Installing Riving KnifeWhen to Use the Riving Knife Riving Knife Spreader or Riving Knife Alignment Checking AlignmentTools Needed Possible Tools Needed Adjusting AlignmentAdjusting Bent Spreader/Riving Knife Follow Checking Alignment, Steps 1-4, on Optional Table Insert D3697-Standard Zero-Clearance Insert New Parts Description =\FjVainBVXcZhVcYIddah Page Contents Introduction Woodstock Technical Support Introduction Introduction Controls and Features Safety Standard Safety Instructions Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Table Saws Preventing Kickback Below are tips to avoid the most common causes of kickback Do not stand directly behind Blade when making a cut Protecting Yourself from Kickback Common Terms W1761 220V Single-Phase Operation W1761 Electrical SpecificationsExtension Cords Phase Converter W1762 220V 3-Phase OperationW1762 440V 3-Phase Operation Electrical Specifications Description Qty Items Needed for Set UpUnpacking Immediately discard all Plastic bags and pack Fence Inventory InventoryMachine Inventory Box Inventory Figure Fence Rail Inventory Extension Table Inventory Cleaning Machine Machine Placement To install the front and rear rails, do these steps Extension Table Leveling main extension table Support Leg Hex Nut Foot Support leg fastened to main Extension table Arbor To install the blade, do these stepsSaw Blade To change the arbor, do these steps Table Insert To install and adjust the table insert, do these stepsTo install the blade guard, do these steps Blade Guard & Splitter To install the riving knife, do these steps Splitter To install the miter gauge, do these steps ON/OFF SwitchTo install the switch, do these steps Miter Gauge Dust Collection Recommended AdjustmentsRecommended adjustment checklist Recommended CFM at Dust Port Test Run To test run the machine, do these steps General Basic Controls Crosscut blade features see Figure Disabling On/Off SwitchRipping blade features see Figure Blade Selection Combination blade features see Figure Laminate blade features see FigureDado Blades see Figure Non-Through Cuts Workpiece InspectionNon-Through Through Cuts Through Cuts Ripping Typical ripping operation To make a crosscut using the miter gauge, do these steps Crosscutting Miter Cuts Blade Tilt & Bevel CutsTo perform a miter cut, do these steps Dado Cutting To use a stacked or wobble dado blade, do these steps Disconnect the SAW from Power Rabbet Cutting To cut rabbets with the dado blade, do these steps To cut rabbets with the standard blade, do these steps First cut to create a rabbet With a standard blade Resawing Resaw Barrier Auxiliary Fence To build the auxiliary fence, do these steps Resawing Operations To perform resawing operations, do these steps Table Saw Accessories D3585 Bore General Purpose D3586 Fine Finishing D3587 100 Operations Daily Check CleaningLubrication Weekly Check Troubleshooting Motor & Electrical Operations W1761/W1762 12 Table Saw with Riving Knife Replacing Flat Belt To remove the flat belt, do these steps To install the new belt, do these steps Deflect it no more than 1⁄8 Blade Tilt Stops To set the 90 stop bolt, do these stepsTo set the 45 stop bolt, do these steps To adjust the tilt indicator arrow, do these steps Digital ReadoutTo set the digital readout, do these steps Example of adjusting blade to Miter slot Miter Slot to Blade Parallelism To adjust the blade by moving the table, do these steps Blade Alignment Adjusting Fence Square and HeightClamping Pressure and Parallelism Miter gauge diagram Switch W1761 magnetic switch W1761 Wiring Diagram See Figure W1762 magnetic switch prewired to 220V, 3-phase W1762 Electrical Components W1762 Wiring Diagram 220V, 3-Phase W1762 Wiring Diagram 440V, 3-Phase Blade Guard Assembly Blade Guard Assembly Parts List Parts Fence Assembly Fence Assembly Parts List Miter Gauge Assembly Miter Gauge Parts List Main Table, Motor & Cabinet Main Table, Motor & Cabinet Parts List Motoraccesscover Mitergaugemountingbracket Extension Table Assembly Extension Table Parts List Label Placement Warranty Page Page Warranty Registration Comments BOX BELLINGHAM, WA