Operations | Woodstock W1762, W1761 specification

W1761/W1762 12" Table Saw with Riving Knife

S&W Digital Calipers are very nice digital calipers with the follow- ing features: Extra large LCD readout. Accuracy: ± 0.001"/ 0.02mm. Resolution: 0.0005/ 0.01mm. Inch and metric digital display.

Stainless steel construction. Built-in computer interface port with automatic shutoff.

SW1082: 4 Digital Caliper

SW1083: 6" Digital Caliper

SW1084: 8" Digital Caliper

High precision Aluminum Squares are perfect for square layouts and machine setup.

D3068: 10" Aluminum Square

D3069: 12" Aluminum Square

D3070: 18" Aluminum Square

D3071: 24" Aluminum Square

D3383: 4" Precision Square

D3384: 6" Precision Square

D3384

The Model W1727 Shop Fox 1 HP Dust Collector is the perfect companion for the Model W1761/W1762. It packs a 1 HP, 110V/220V, single-phase motor and 800 CFM air suction capacity.

-43-

OPERATIONS

Image 57

Woodstock W1762, W1761 owner manual Operations

Contents

Table SAW with Riving Knife Inventory Differences Important Changes to Assembly Blade Installation Blade RequirementsBlade Size Requirements Blade Guard GuardSpreader Location to secure blade guard Screw Installing Blade Guard & Spreader To remove the pawls, do these steps Anti-Kickback Pawls When Not to Use the Blade Guard When to Use the Blade Guard When to Use the Riving Knife Installing Riving KnifeWhen Not to Use the Riving Knife Riving Knife Spreader or Riving Knife Alignment Checking AlignmentTools Needed Adjusting Bent Spreader/Riving Knife Adjusting AlignmentPossible Tools Needed Follow Checking Alignment, Steps 1-4, on D3697-Standard Zero-Clearance Insert Optional Table Insert Description New Parts =\FjVainBVXcZhVcYIddah Page Contents Woodstock Technical Support Introduction Introduction Introduction Controls and Features Standard Safety Instructions Safety Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Table Saws Below are tips to avoid the most common causes of kickback Preventing Kickback Protecting Yourself from Kickback Do not stand directly behind Blade when making a cut Common Terms W1761 220V Single-Phase Operation W1761 Electrical SpecificationsExtension Cords W1762 440V 3-Phase Operation W1762 220V 3-Phase OperationPhase Converter Electrical Specifications Unpacking Items Needed for Set UpDescription Qty Immediately discard all Plastic bags and pack Machine Inventory InventoryFence Inventory Box Inventory Figure Extension Table Inventory Fence Rail Inventory Machine Placement Cleaning Machine Extension Table To install the front and rear rails, do these steps Leveling main extension table Support Leg Hex Nut Foot Support leg fastened to main Extension table Saw Blade To install the blade, do these stepsArbor To change the arbor, do these steps To install the blade guard, do these steps To install and adjust the table insert, do these stepsTable Insert Blade Guard & Splitter Splitter To install the riving knife, do these steps To install the switch, do these steps ON/OFF SwitchTo install the miter gauge, do these steps Miter Gauge Recommended adjustment checklist Recommended AdjustmentsDust Collection Recommended CFM at Dust Port To test run the machine, do these steps Test Run Basic Controls General Ripping blade features see Figure Disabling On/Off SwitchCrosscut blade features see Figure Blade Selection Combination blade features see Figure Laminate blade features see FigureDado Blades see Figure Non-Through Through Cuts Workpiece InspectionNon-Through Cuts Through Cuts Typical ripping operation Ripping Crosscutting To make a crosscut using the miter gauge, do these steps Miter Cuts Blade Tilt & Bevel CutsTo perform a miter cut, do these steps To use a stacked or wobble dado blade, do these steps Dado Cutting Disconnect the SAW from Power To cut rabbets with the dado blade, do these steps Rabbet Cutting First cut to create a rabbet With a standard blade To cut rabbets with the standard blade, do these steps Resaw Barrier Resawing To build the auxiliary fence, do these steps Auxiliary Fence To perform resawing operations, do these steps Resawing Operations Table Saw Accessories D3585 Bore General Purpose D3586 Fine Finishing D3587 100 Operations Lubrication CleaningDaily Check Weekly Check Motor & Electrical Troubleshooting W1761/W1762 12 Table Saw with Riving Knife Operations To remove the flat belt, do these steps Replacing Flat Belt Deflect it no more than 1⁄8 To install the new belt, do these steps Blade Tilt Stops To set the 90 stop bolt, do these stepsTo set the 45 stop bolt, do these steps To adjust the tilt indicator arrow, do these steps Digital ReadoutTo set the digital readout, do these steps Miter Slot to Blade Parallelism Example of adjusting blade to Miter slot Blade Alignment To adjust the blade by moving the table, do these steps Adjusting Fence Square and HeightClamping Pressure and Parallelism Miter gauge diagram W1761 magnetic switch Switch See Figure W1761 Wiring Diagram W1762 Electrical Components W1762 magnetic switch prewired to 220V, 3-phase W1762 Wiring Diagram 220V, 3-Phase W1762 Wiring Diagram 440V, 3-Phase Parts Blade Guard Assembly Blade Guard Assembly Parts List Fence Assembly Fence Assembly Parts List Miter Gauge Assembly Miter Gauge Parts List Main Table, Motor & Cabinet Motoraccesscover Main Table, Motor & Cabinet Parts List Mitergaugemountingbracket Extension Table Assembly Extension Table Parts List Label Placement Warranty Page Page Comments Warranty Registration BOX BELLINGHAM, WA