Extension Table | Woodstock W1761, W1762 specification

W1761/W1762 12" Table Saw with Riving Knife

Extension Table

SET UP

To install the front and rear rails, do these steps:

1.Fasten the 93" front rail onto the table saw with five M8-1.25 x 25 flat head screws as shown in Figure

13. Secure the flat head screw on the far left with a flat washer, lock washer, and hex nut.

2.Fasten the 79" rear rail to the table with five M8- 1.25 x 25 cap screws as shown in Figure 14. Secure the cap screw on the far right with a flat washer, lock nut, and hex nut.

3.Thread two M10-1.5 x 25 hex bolts with flat wash- ers onto the right side of the table saw cabinet as shown in Figure 15. Do not fully tighten the bolts.

4.With the help of an assistant, place the extension table between the rails and slide the table slots over the bolts installed in Step 3.

Figure 13. Front rail installed.

Figure 14. Rear rail installed.

Hex Bolts

Figure 15. Hex bolts installed.

-18-

Image 32

Woodstock W1761, W1762 owner manual Extension Table, To install the front and rear rails, do these steps

Contents

Table SAW with Riving Knife Important Changes to Assembly Inventory Differences Blade Size Requirements Blade InstallationBlade Requirements Spreader Blade GuardGuard Installing Blade Guard & Spreader Location to secure blade guard Screw Anti-Kickback Pawls To remove the pawls, do these steps When to Use the Blade Guard When Not to Use the Blade Guard Installing Riving Knife When to Use the Riving KnifeWhen Not to Use the Riving Knife Riving Knife Tools Needed Spreader or Riving Knife AlignmentChecking Alignment Adjusting Alignment Adjusting Bent Spreader/Riving KnifePossible Tools Needed Follow Checking Alignment, Steps 1-4, on Optional Table Insert D3697-Standard Zero-Clearance Insert New Parts Description =\FjVainBVXcZhVcYIddah Page Contents Introduction Woodstock Technical Support Introduction Introduction Controls and Features Safety Standard Safety Instructions Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Table Saws Preventing Kickback Below are tips to avoid the most common causes of kickback Do not stand directly behind Blade when making a cut Protecting Yourself from Kickback Common Terms Extension Cords W1761 220V Single-Phase OperationW1761 Electrical Specifications W1762 220V 3-Phase Operation W1762 440V 3-Phase OperationPhase Converter Electrical Specifications Items Needed for Set Up UnpackingDescription Qty Immediately discard all Plastic bags and pack Inventory Machine InventoryFence Inventory Box Inventory Figure Fence Rail Inventory Extension Table Inventory Cleaning Machine Machine Placement To install the front and rear rails, do these steps Extension Table Leveling main extension table Support Leg Hex Nut Foot Support leg fastened to main Extension table To install the blade, do these steps Saw BladeArbor To change the arbor, do these steps To install and adjust the table insert, do these steps To install the blade guard, do these stepsTable Insert Blade Guard & Splitter To install the riving knife, do these steps Splitter ON/OFF Switch To install the switch, do these stepsTo install the miter gauge, do these steps Miter Gauge Recommended Adjustments Recommended adjustment checklistDust Collection Recommended CFM at Dust Port Test Run To test run the machine, do these steps General Basic Controls Disabling On/Off Switch Ripping blade features see FigureCrosscut blade features see Figure Blade Selection Dado Blades see Figure Combination blade features see FigureLaminate blade features see Figure Workpiece Inspection Non-Through Through CutsNon-Through Cuts Through Cuts Ripping Typical ripping operation To make a crosscut using the miter gauge, do these steps Crosscutting To perform a miter cut, do these steps Miter CutsBlade Tilt & Bevel Cuts Dado Cutting To use a stacked or wobble dado blade, do these steps Disconnect the SAW from Power Rabbet Cutting To cut rabbets with the dado blade, do these steps To cut rabbets with the standard blade, do these steps First cut to create a rabbet With a standard blade Resawing Resaw Barrier Auxiliary Fence To build the auxiliary fence, do these steps Resawing Operations To perform resawing operations, do these steps Table Saw Accessories D3585 Bore General Purpose D3586 Fine Finishing D3587 100 Operations Cleaning LubricationDaily Check Weekly Check Troubleshooting Motor & Electrical Operations W1761/W1762 12 Table Saw with Riving Knife Replacing Flat Belt To remove the flat belt, do these steps To install the new belt, do these steps Deflect it no more than 1⁄8 To set the 45 stop bolt, do these steps Blade Tilt StopsTo set the 90 stop bolt, do these steps To set the digital readout, do these steps To adjust the tilt indicator arrow, do these stepsDigital Readout Example of adjusting blade to Miter slot Miter Slot to Blade Parallelism To adjust the blade by moving the table, do these steps Blade Alignment Clamping Pressure and Parallelism Adjusting FenceSquare and Height Miter gauge diagram Switch W1761 magnetic switch W1761 Wiring Diagram See Figure W1762 magnetic switch prewired to 220V, 3-phase W1762 Electrical Components W1762 Wiring Diagram 220V, 3-Phase W1762 Wiring Diagram 440V, 3-Phase Blade Guard Assembly Blade Guard Assembly Parts List Parts Fence Assembly Fence Assembly Parts List Miter Gauge Assembly Miter Gauge Parts List Main Table, Motor & Cabinet Main Table, Motor & Cabinet Parts List Motoraccesscover Mitergaugemountingbracket Extension Table Assembly Extension Table Parts List Label Placement Warranty Page Page Warranty Registration Comments BOX BELLINGHAM, WA