ON/OFF Switch, Miter Gauge, Fence Components | Woodstock W1761

W1761/W1762 12" Table Saw with Riving Knife

SET UP

ON/OFF Switch

To install the switch, do these steps:

1.Fasten the switch to the left end of the front rail with two M8-1.25 x 25 flange bolts, and install the anti-start safety pin as shown in Figure 32.

Miter Gauge

To install the miter gauge, do these steps:

1.Install the miter gauge handle and 8mm flat washer onto the miter gauge as shown in Figure 33.

2.Slide the miter gauge into the miter gauge slot to the left of the blade; or store it temporarily on the brackets near the blade angle handwheel.

Fence Components

To install the fence knobs, fence, and fence resting brackets, do these steps:

1.Install the fence knob as shown in Figure 34.

2.Install the fence onto the table to the right of the blade.

3.Check for fence parallelism and adjust if needed. See Adjusting Fence on Page 53.

4.Install the fence resting brackets (Figure 35) onto the back of the cabinet with two flange bolts.

-24-

Figure 32. Switch installed.

Handle Washer

Figure 33. Miter gauge installed.

Figure 34. Fence knob installed.

Brackets

Figure 35. Fence resting brackets

installed.

Image 38

Woodstock W1761, W1762 owner manual ON/OFF Switch, Miter Gauge, Fence Components, To install the switch, do these steps

Contents

Table SAW with Riving Knife Important Changes to Assembly Inventory Differences Blade Size Requirements Blade InstallationBlade Requirements Spreader Blade GuardGuard Installing Blade Guard & Spreader Location to secure blade guard Screw Anti-Kickback Pawls To remove the pawls, do these steps When to Use the Blade Guard When Not to Use the Blade Guard When Not to Use the Riving Knife Installing Riving KnifeWhen to Use the Riving Knife Riving Knife Tools Needed Spreader or Riving Knife AlignmentChecking Alignment Possible Tools Needed Adjusting AlignmentAdjusting Bent Spreader/Riving Knife Follow Checking Alignment, Steps 1-4, on Optional Table Insert D3697-Standard Zero-Clearance Insert New Parts Description =\FjVainBVXcZhVcYIddah Page Contents Introduction Woodstock Technical Support Introduction Introduction Controls and Features Safety Standard Safety Instructions Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Table Saws Preventing Kickback Below are tips to avoid the most common causes of kickback Do not stand directly behind Blade when making a cut Protecting Yourself from Kickback Common Terms Extension Cords W1761 220V Single-Phase OperationW1761 Electrical Specifications Phase Converter W1762 220V 3-Phase OperationW1762 440V 3-Phase Operation Electrical Specifications Description Qty Items Needed for Set UpUnpacking Immediately discard all Plastic bags and pack Fence Inventory InventoryMachine Inventory Box Inventory Figure Fence Rail Inventory Extension Table Inventory Cleaning Machine Machine Placement To install the front and rear rails, do these steps Extension Table Leveling main extension table Support Leg Hex Nut Foot Support leg fastened to main Extension table Arbor To install the blade, do these stepsSaw Blade To change the arbor, do these steps Table Insert To install and adjust the table insert, do these stepsTo install the blade guard, do these steps Blade Guard & Splitter To install the riving knife, do these steps Splitter To install the miter gauge, do these steps ON/OFF SwitchTo install the switch, do these steps Miter Gauge Dust Collection Recommended AdjustmentsRecommended adjustment checklist Recommended CFM at Dust Port Test Run To test run the machine, do these steps General Basic Controls Crosscut blade features see Figure Disabling On/Off SwitchRipping blade features see Figure Blade Selection Dado Blades see Figure Combination blade features see FigureLaminate blade features see Figure Non-Through Cuts Workpiece InspectionNon-Through Through Cuts Through Cuts Ripping Typical ripping operation To make a crosscut using the miter gauge, do these steps Crosscutting To perform a miter cut, do these steps Miter CutsBlade Tilt & Bevel Cuts Dado Cutting To use a stacked or wobble dado blade, do these steps Disconnect the SAW from Power Rabbet Cutting To cut rabbets with the dado blade, do these steps To cut rabbets with the standard blade, do these steps First cut to create a rabbet With a standard blade Resawing Resaw Barrier Auxiliary Fence To build the auxiliary fence, do these steps Resawing Operations To perform resawing operations, do these steps Table Saw Accessories D3585 Bore General Purpose D3586 Fine Finishing D3587 100 Operations Daily Check CleaningLubrication Weekly Check Troubleshooting Motor & Electrical Operations W1761/W1762 12 Table Saw with Riving Knife Replacing Flat Belt To remove the flat belt, do these steps To install the new belt, do these steps Deflect it no more than 1⁄8 To set the 45 stop bolt, do these steps Blade Tilt StopsTo set the 90 stop bolt, do these steps To set the digital readout, do these steps To adjust the tilt indicator arrow, do these stepsDigital Readout Example of adjusting blade to Miter slot Miter Slot to Blade Parallelism To adjust the blade by moving the table, do these steps Blade Alignment Clamping Pressure and Parallelism Adjusting FenceSquare and Height Miter gauge diagram Switch W1761 magnetic switch W1761 Wiring Diagram See Figure W1762 magnetic switch prewired to 220V, 3-phase W1762 Electrical Components W1762 Wiring Diagram 220V, 3-Phase W1762 Wiring Diagram 440V, 3-Phase Blade Guard Assembly Blade Guard Assembly Parts List Parts Fence Assembly Fence Assembly Parts List Miter Gauge Assembly Miter Gauge Parts List Main Table, Motor & Cabinet Main Table, Motor & Cabinet Parts List Motoraccesscover Mitergaugemountingbracket Extension Table Assembly Extension Table Parts List Label Placement Warranty Page Page Warranty Registration Comments BOX BELLINGHAM, WA