Machine Inventory, Fence Inventory | Woodstock W1762, W1761 guide

W1761/W1762 12" Table Saw with Riving Knife

Inventory

The following is a description of the main components shipped with the SHOP FOX® Model W1761⁄W1762. Lay the components out to inventory them.

Note: If you can't find an item on this list, check the mounting location on the machine or examine the pack- aging materials carefully. Occasionally we pre-install cer- tain components for safer shipping.

Machine Inventory
Box Inventory (Figure 9)		Qty
A.	Splitter/Guard Assembly	1
B.	Miter Gauge Handle	1
C.	Miter Gauge	1
D.	Handwheel Handles	2
E.	Arbor Extension 5⁄8"-18 x 11⁄4"	1
F.	Arbor Nut 5⁄8-18	1
G.	Arbor Flange 5⁄8"	1
H.	Arbor Wrenches	2
I.	Fence Resting Brackets	2
Tools and Hardware (Not Shown)		Qty
•	Flat Washer 8mm (Miter Gauge)	1

A

H

G F

D

E

I

B

C

SET UP

• Flange Bolts M8-1.25 x 12 (Switch)	2
• Flange Bolts M8-1.25 x 12 (Fence Brackets)	2
• Hex Wrenches 3, 4, 5, 6mm	1 Each
• Open-End Wrenches
8 x 10, 11 x 13, 14 x 17	1 Each
• Screwdriver, Phillips/Flat	1

Figure 9. Main components.

Fence Inventory
Box Inventory (Figure 10)		Qty
A.	Fence	1
B.	Fence Handle	1

A

B

Figure 10. Fence components.

-15-

Image 29

Woodstock W1762, W1761 Machine Inventory, Fence Inventory, Box Inventory Figure, Tools and Hardware Not Shown

Contents

Table SAW with Riving Knife Inventory Differences Important Changes to Assembly Blade Size Requirements Blade InstallationBlade Requirements Spreader Blade GuardGuard Location to secure blade guard Screw Installing Blade Guard & Spreader To remove the pawls, do these steps Anti-Kickback Pawls When Not to Use the Blade Guard When to Use the Blade Guard When to Use the Riving Knife Installing Riving KnifeWhen Not to Use the Riving Knife Riving Knife Tools Needed Spreader or Riving Knife AlignmentChecking Alignment Adjusting Bent Spreader/Riving Knife Adjusting AlignmentPossible Tools Needed Follow Checking Alignment, Steps 1-4, on D3697-Standard Zero-Clearance Insert Optional Table Insert Description New Parts =\FjVainBVXcZhVcYIddah Page Contents Woodstock Technical Support Introduction Introduction Introduction Controls and Features Standard Safety Instructions Safety Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Table Saws Below are tips to avoid the most common causes of kickback Preventing Kickback Protecting Yourself from Kickback Do not stand directly behind Blade when making a cut Common Terms Extension Cords W1761 220V Single-Phase OperationW1761 Electrical Specifications W1762 440V 3-Phase Operation W1762 220V 3-Phase OperationPhase Converter Electrical Specifications Unpacking Items Needed for Set UpDescription Qty Immediately discard all Plastic bags and pack Machine Inventory InventoryFence Inventory Box Inventory Figure Extension Table Inventory Fence Rail Inventory Machine Placement Cleaning Machine Extension Table To install the front and rear rails, do these steps Leveling main extension table Support Leg Hex Nut Foot Support leg fastened to main Extension table Saw Blade To install the blade, do these stepsArbor To change the arbor, do these steps To install the blade guard, do these steps To install and adjust the table insert, do these stepsTable Insert Blade Guard & Splitter Splitter To install the riving knife, do these steps To install the switch, do these steps ON/OFF SwitchTo install the miter gauge, do these steps Miter Gauge Recommended adjustment checklist Recommended AdjustmentsDust Collection Recommended CFM at Dust Port To test run the machine, do these steps Test Run Basic Controls General Ripping blade features see Figure Disabling On/Off SwitchCrosscut blade features see Figure Blade Selection Dado Blades see Figure Combination blade features see FigureLaminate blade features see Figure Non-Through Through Cuts Workpiece InspectionNon-Through Cuts Through Cuts Typical ripping operation Ripping Crosscutting To make a crosscut using the miter gauge, do these steps To perform a miter cut, do these steps Miter CutsBlade Tilt & Bevel Cuts To use a stacked or wobble dado blade, do these steps Dado Cutting Disconnect the SAW from Power To cut rabbets with the dado blade, do these steps Rabbet Cutting First cut to create a rabbet With a standard blade To cut rabbets with the standard blade, do these steps Resaw Barrier Resawing To build the auxiliary fence, do these steps Auxiliary Fence To perform resawing operations, do these steps Resawing Operations Table Saw Accessories D3585 Bore General Purpose D3586 Fine Finishing D3587 100 Operations Lubrication CleaningDaily Check Weekly Check Motor & Electrical Troubleshooting W1761/W1762 12 Table Saw with Riving Knife Operations To remove the flat belt, do these steps Replacing Flat Belt Deflect it no more than 1⁄8 To install the new belt, do these steps To set the 45 stop bolt, do these steps Blade Tilt StopsTo set the 90 stop bolt, do these steps To set the digital readout, do these steps To adjust the tilt indicator arrow, do these stepsDigital Readout Miter Slot to Blade Parallelism Example of adjusting blade to Miter slot Blade Alignment To adjust the blade by moving the table, do these steps Clamping Pressure and Parallelism Adjusting FenceSquare and Height Miter gauge diagram W1761 magnetic switch Switch See Figure W1761 Wiring Diagram W1762 Electrical Components W1762 magnetic switch prewired to 220V, 3-phase W1762 Wiring Diagram 220V, 3-Phase W1762 Wiring Diagram 440V, 3-Phase Parts Blade Guard Assembly Blade Guard Assembly Parts List Fence Assembly Fence Assembly Parts List Miter Gauge Assembly Miter Gauge Parts List Main Table, Motor & Cabinet Motoraccesscover Main Table, Motor & Cabinet Parts List Mitergaugemountingbracket Extension Table Assembly Extension Table Parts List Label Placement Warranty Page Page Comments Warranty Registration BOX BELLINGHAM, WA