When to Use the Blade Guard | Woodstock W1762, W1761 specification

Model W1761/W1762 (M-1/10, S7/10+)

Re-installing Pawls

1.Loosen the knob on top of the spreader, then remove the blade guard.

2.Slide the pin in the pawl block into the second groove from the front of the spreader, as shown in Figure 10.

3.Press the button on the pawl block shown in Figure 9, then pivot the pawls down until they lock into place.

4.Re-install the blade guard onto the spreader and secure with the top knob.

When to Use the Blade Guard

The blade guard assembly MUST always be installed on the saw for all normal through cuts (those where the blade cuts all the way through the thickness of the workpiece).

When Not to Use the Blade Guard

The blade guard cannot be used for any non-through cuts (those in which the blade does not cut all the way through the thickness of the workpiece).

Sometimes the blade guard or its components can get in the way when cutting very narrow workpieces or other specialized cuts. Because the blade guard is provided to decrease your risk of injury, it should not be used if it gets in the way of making a safe cut. Use good judgment!

IMPORTANT: Whenever the blade guard cannot be used, the riving knife must be installed.

-6-

Groove

Pin

Figure 10. Re-installing pawls.

Image 7

Woodstock W1762, W1761 owner manual When to Use the Blade Guard, When Not to Use the Blade Guard

Contents

Table SAW with Riving Knife Inventory Differences Important Changes to Assembly Blade Requirements Blade InstallationBlade Size Requirements Guard Blade GuardSpreader Location to secure blade guard Screw Installing Blade Guard & Spreader To remove the pawls, do these steps Anti-Kickback Pawls When Not to Use the Blade Guard When to Use the Blade Guard Riving Knife Installing Riving KnifeWhen to Use the Riving Knife When Not to Use the Riving Knife Checking Alignment Spreader or Riving Knife AlignmentTools Needed Follow Checking Alignment, Steps 1-4, on Adjusting AlignmentAdjusting Bent Spreader/Riving Knife Possible Tools Needed D3697-Standard Zero-Clearance Insert Optional Table Insert Description New Parts =\FjVainBVXcZhVcYIddah Page Contents Woodstock Technical Support Introduction Introduction Introduction Controls and Features Standard Safety Instructions Safety Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Table Saws Below are tips to avoid the most common causes of kickback Preventing Kickback Protecting Yourself from Kickback Do not stand directly behind Blade when making a cut Common Terms W1761 Electrical Specifications W1761 220V Single-Phase OperationExtension Cords Electrical Specifications W1762 220V 3-Phase OperationW1762 440V 3-Phase Operation Phase Converter Immediately discard all Plastic bags and pack Items Needed for Set UpUnpacking Description Qty Box Inventory Figure InventoryMachine Inventory Fence Inventory Extension Table Inventory Fence Rail Inventory Machine Placement Cleaning Machine Extension Table To install the front and rear rails, do these steps Leveling main extension table Support Leg Hex Nut Foot Support leg fastened to main Extension table To change the arbor, do these steps To install the blade, do these stepsSaw Blade Arbor Blade Guard & Splitter To install and adjust the table insert, do these stepsTo install the blade guard, do these steps Table Insert Splitter To install the riving knife, do these steps Miter Gauge ON/OFF SwitchTo install the switch, do these steps To install the miter gauge, do these steps Recommended CFM at Dust Port Recommended AdjustmentsRecommended adjustment checklist Dust Collection To test run the machine, do these steps Test Run Basic Controls General Blade Selection Disabling On/Off SwitchRipping blade features see Figure Crosscut blade features see Figure Laminate blade features see Figure Combination blade features see FigureDado Blades see Figure Through Cuts Workpiece InspectionNon-Through Through Cuts Non-Through Cuts Typical ripping operation Ripping Crosscutting To make a crosscut using the miter gauge, do these steps Blade Tilt & Bevel Cuts Miter CutsTo perform a miter cut, do these steps To use a stacked or wobble dado blade, do these steps Dado Cutting Disconnect the SAW from Power To cut rabbets with the dado blade, do these steps Rabbet Cutting First cut to create a rabbet With a standard blade To cut rabbets with the standard blade, do these steps Resaw Barrier Resawing To build the auxiliary fence, do these steps Auxiliary Fence To perform resawing operations, do these steps Resawing Operations Table Saw Accessories D3585 Bore General Purpose D3586 Fine Finishing D3587 100 Operations Weekly Check CleaningLubrication Daily Check Motor & Electrical Troubleshooting W1761/W1762 12 Table Saw with Riving Knife Operations To remove the flat belt, do these steps Replacing Flat Belt Deflect it no more than 1⁄8 To install the new belt, do these steps To set the 90 stop bolt, do these steps Blade Tilt StopsTo set the 45 stop bolt, do these steps Digital Readout To adjust the tilt indicator arrow, do these stepsTo set the digital readout, do these steps Miter Slot to Blade Parallelism Example of adjusting blade to Miter slot Blade Alignment To adjust the blade by moving the table, do these steps Square and Height Adjusting FenceClamping Pressure and Parallelism Miter gauge diagram W1761 magnetic switch Switch See Figure W1761 Wiring Diagram W1762 Electrical Components W1762 magnetic switch prewired to 220V, 3-phase W1762 Wiring Diagram 220V, 3-Phase W1762 Wiring Diagram 440V, 3-Phase Parts Blade Guard Assembly Blade Guard Assembly Parts List Fence Assembly Fence Assembly Parts List Miter Gauge Assembly Miter Gauge Parts List Main Table, Motor & Cabinet Motoraccesscover Main Table, Motor & Cabinet Parts List Mitergaugemountingbracket Extension Table Assembly Extension Table Parts List Label Placement Warranty Page Page Comments Warranty Registration BOX BELLINGHAM, WA