W1762 Electrical Components | Woodstock W1761 instruction

W1761/W1762 12" Table Saw with Riving Knife

W1762 Electrical Components

Figure 83. W1762 magnetic switch prewired to

220V, 3-phase.

Note: The thermal relay in Figure 83 is set for 22 amp, 220V, 3-phase operation.

Figure 84. W1762 magnetic switch converted

to 440V, 3-phase.

Note: The thermal relay in Figure 84 is adjusted for 11 amp, 440V, 3-phase operation.

SERVICE

-57-

Image 71

Woodstock W1761 owner manual W1762 Electrical Components, W1762 magnetic switch prewired to 220V, 3-phase

Contents

Table SAW with Riving Knife Inventory Differences Important Changes to Assembly Blade Size Requirements Blade InstallationBlade Requirements Spreader Blade GuardGuard Location to secure blade guard Screw Installing Blade Guard & Spreader To remove the pawls, do these steps Anti-Kickback Pawls When Not to Use the Blade Guard When to Use the Blade Guard Riving Knife Installing Riving KnifeWhen to Use the Riving Knife When Not to Use the Riving Knife Tools Needed Spreader or Riving Knife AlignmentChecking Alignment Follow Checking Alignment, Steps 1-4, on Adjusting AlignmentAdjusting Bent Spreader/Riving Knife Possible Tools Needed D3697-Standard Zero-Clearance Insert Optional Table Insert Description New Parts =\FjVainBVXcZhVcYIddah Page Contents Woodstock Technical Support Introduction Introduction Introduction Controls and Features Standard Safety Instructions Safety Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Table Saws Below are tips to avoid the most common causes of kickback Preventing Kickback Protecting Yourself from Kickback Do not stand directly behind Blade when making a cut Common Terms Extension Cords W1761 220V Single-Phase OperationW1761 Electrical Specifications Electrical Specifications W1762 220V 3-Phase OperationW1762 440V 3-Phase Operation Phase Converter Immediately discard all Plastic bags and pack Items Needed for Set UpUnpacking Description Qty Box Inventory Figure InventoryMachine Inventory Fence Inventory Extension Table Inventory Fence Rail Inventory Machine Placement Cleaning Machine Extension Table To install the front and rear rails, do these steps Leveling main extension table Support Leg Hex Nut Foot Support leg fastened to main Extension table To change the arbor, do these steps To install the blade, do these stepsSaw Blade Arbor Blade Guard & Splitter To install and adjust the table insert, do these stepsTo install the blade guard, do these steps Table Insert Splitter To install the riving knife, do these steps Miter Gauge ON/OFF SwitchTo install the switch, do these steps To install the miter gauge, do these steps Recommended CFM at Dust Port Recommended AdjustmentsRecommended adjustment checklist Dust Collection To test run the machine, do these steps Test Run Basic Controls General Blade Selection Disabling On/Off SwitchRipping blade features see Figure Crosscut blade features see Figure Dado Blades see Figure Combination blade features see FigureLaminate blade features see Figure Through Cuts Workpiece InspectionNon-Through Through Cuts Non-Through Cuts Typical ripping operation Ripping Crosscutting To make a crosscut using the miter gauge, do these steps To perform a miter cut, do these steps Miter CutsBlade Tilt & Bevel Cuts To use a stacked or wobble dado blade, do these steps Dado Cutting Disconnect the SAW from Power To cut rabbets with the dado blade, do these steps Rabbet Cutting First cut to create a rabbet With a standard blade To cut rabbets with the standard blade, do these steps Resaw Barrier Resawing To build the auxiliary fence, do these steps Auxiliary Fence To perform resawing operations, do these steps Resawing Operations Table Saw Accessories D3585 Bore General Purpose D3586 Fine Finishing D3587 100 Operations Weekly Check CleaningLubrication Daily Check Motor & Electrical Troubleshooting W1761/W1762 12 Table Saw with Riving Knife Operations To remove the flat belt, do these steps Replacing Flat Belt Deflect it no more than 1⁄8 To install the new belt, do these steps To set the 45 stop bolt, do these steps Blade Tilt StopsTo set the 90 stop bolt, do these steps To set the digital readout, do these steps To adjust the tilt indicator arrow, do these stepsDigital Readout Miter Slot to Blade Parallelism Example of adjusting blade to Miter slot Blade Alignment To adjust the blade by moving the table, do these steps Clamping Pressure and Parallelism Adjusting FenceSquare and Height Miter gauge diagram W1761 magnetic switch Switch See Figure W1761 Wiring Diagram W1762 Electrical Components W1762 magnetic switch prewired to 220V, 3-phase W1762 Wiring Diagram 220V, 3-Phase W1762 Wiring Diagram 440V, 3-Phase Parts Blade Guard Assembly Blade Guard Assembly Parts List Fence Assembly Fence Assembly Parts List Miter Gauge Assembly Miter Gauge Parts List Main Table, Motor & Cabinet Motoraccesscover Main Table, Motor & Cabinet Parts List Mitergaugemountingbracket Extension Table Assembly Extension Table Parts List Label Placement Warranty Page Page Comments Warranty Registration BOX BELLINGHAM, WA