Support leg fastened to main Extension table | Woodstock W1761

W1761/W1762 12" Table Saw with Riving Knife

SET UP

11.Fasten each support leg to the main extension table with four M6-1 x 12 Phillips head screws and flat washers as shown in Figure 20.

12.Rotate both feet until they touch the ground, and tighten the hex nuts to secure the feet.

13.Fasten the shelf end plate to the legs with four M6-1 x 12 Phillips head screws and flat washers as shown in Figure 21.

14.Place the shelf brackets between the cabinet and shelf end plate, and fasten with four M6-1 x 12 hex bolts, and two flat washers and two hex nuts (on the end plate), as shown in Figure 22.

15.Place the lower shelf on the brackets.

16.Place the 93" fence tube over the 93" front rail and secure with nine M8-1.25 x 12 flange bolts as shown in Figure 23.

-20-

Figure 20. Support leg fastened to main

extension table.

Figure 21. Installing shelf end plate on

extension table legs.

Flange

Shelf Bracket

Figure 22. Shelf brackets installed.

Flange Bolt

Figure 23. Fence tube mounted to front

fence rail.

Image 34

Woodstock W1761, W1762 owner manual Support leg fastened to main Extension table

Contents

Table SAW with Riving Knife Important Changes to Assembly Inventory Differences Blade Requirements Blade InstallationBlade Size Requirements Guard Blade GuardSpreader Installing Blade Guard & Spreader Location to secure blade guard Screw Anti-Kickback Pawls To remove the pawls, do these steps When to Use the Blade Guard When Not to Use the Blade Guard When Not to Use the Riving Knife Installing Riving KnifeWhen to Use the Riving Knife Riving Knife Checking Alignment Spreader or Riving Knife AlignmentTools Needed Possible Tools Needed Adjusting AlignmentAdjusting Bent Spreader/Riving Knife Follow Checking Alignment, Steps 1-4, on Optional Table Insert D3697-Standard Zero-Clearance Insert New Parts Description =\FjVainBVXcZhVcYIddah Page Contents Introduction Woodstock Technical Support Introduction Introduction Controls and Features Safety Standard Safety Instructions Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Table Saws Preventing Kickback Below are tips to avoid the most common causes of kickback Do not stand directly behind Blade when making a cut Protecting Yourself from Kickback Common Terms W1761 Electrical Specifications W1761 220V Single-Phase OperationExtension Cords Phase Converter W1762 220V 3-Phase OperationW1762 440V 3-Phase Operation Electrical Specifications Description Qty Items Needed for Set UpUnpacking Immediately discard all Plastic bags and pack Fence Inventory InventoryMachine Inventory Box Inventory Figure Fence Rail Inventory Extension Table Inventory Cleaning Machine Machine Placement To install the front and rear rails, do these steps Extension Table Leveling main extension table Support Leg Hex Nut Foot Support leg fastened to main Extension table Arbor To install the blade, do these stepsSaw Blade To change the arbor, do these steps Table Insert To install and adjust the table insert, do these stepsTo install the blade guard, do these steps Blade Guard & Splitter To install the riving knife, do these steps Splitter To install the miter gauge, do these steps ON/OFF SwitchTo install the switch, do these steps Miter Gauge Dust Collection Recommended AdjustmentsRecommended adjustment checklist Recommended CFM at Dust Port Test Run To test run the machine, do these steps General Basic Controls Crosscut blade features see Figure Disabling On/Off SwitchRipping blade features see Figure Blade Selection Laminate blade features see Figure Combination blade features see FigureDado Blades see Figure Non-Through Cuts Workpiece InspectionNon-Through Through Cuts Through Cuts Ripping Typical ripping operation To make a crosscut using the miter gauge, do these steps Crosscutting Blade Tilt & Bevel Cuts Miter CutsTo perform a miter cut, do these steps Dado Cutting To use a stacked or wobble dado blade, do these steps Disconnect the SAW from Power Rabbet Cutting To cut rabbets with the dado blade, do these steps To cut rabbets with the standard blade, do these steps First cut to create a rabbet With a standard blade Resawing Resaw Barrier Auxiliary Fence To build the auxiliary fence, do these steps Resawing Operations To perform resawing operations, do these steps Table Saw Accessories D3585 Bore General Purpose D3586 Fine Finishing D3587 100 Operations Daily Check CleaningLubrication Weekly Check Troubleshooting Motor & Electrical Operations W1761/W1762 12 Table Saw with Riving Knife Replacing Flat Belt To remove the flat belt, do these steps To install the new belt, do these steps Deflect it no more than 1⁄8 To set the 90 stop bolt, do these steps Blade Tilt StopsTo set the 45 stop bolt, do these steps Digital Readout To adjust the tilt indicator arrow, do these stepsTo set the digital readout, do these steps Example of adjusting blade to Miter slot Miter Slot to Blade Parallelism To adjust the blade by moving the table, do these steps Blade Alignment Square and Height Adjusting FenceClamping Pressure and Parallelism Miter gauge diagram Switch W1761 magnetic switch W1761 Wiring Diagram See Figure W1762 magnetic switch prewired to 220V, 3-phase W1762 Electrical Components W1762 Wiring Diagram 220V, 3-Phase W1762 Wiring Diagram 440V, 3-Phase Blade Guard Assembly Blade Guard Assembly Parts List Parts Fence Assembly Fence Assembly Parts List Miter Gauge Assembly Miter Gauge Parts List Main Table, Motor & Cabinet Main Table, Motor & Cabinet Parts List Motoraccesscover Mitergaugemountingbracket Extension Table Assembly Extension Table Parts List Label Placement Warranty Page Page Warranty Registration Comments BOX BELLINGHAM, WA