Xantrex Technology RS232-XHR on page 34

Installation and Configuration

Initial Inspection

20 Operating Manual for RS-232 for XHR/XFR Series Power Supply

Figure 2.1

Power Supply Front Panel with RS-232 Interface Installed (1200 Watt Power Supply Shown)

!

CAUTION

Use proper static control techniques to avoid damage to static-sensitive components

on the printed circuit board.

Address LED (ADR)

Indicates that the master controller is addressing the unit.

Service Request LED (SRQ)

Comes on at power up if the PON SRQ switch is set to

on. You can enable the SRQ LED during normal

operation with the SRQ command.

Error LED (ERR)

Indicates when a programming error has occurred. You

can clear the ERR LED with an error query command.

Fault LED (FLT)

Indicates that a fault has occurred. The fault bit

must be unmasked. Refer to the status register in

Table 3.8, on page 52. Momentarily lights if PON

SRQ is set to on.

Polarity LED (POL)

Indicates that the polarity user line has been

activated. See “Connector J7 User Signals”

on page 34.

Local Switch (LOCAL)Remote LED (REM)

Remote Programming LEDs:

Contents

Main Page Page Limited Warranty Page Disclaimer Exclusions Page Page About This Manual Main Sections Manual Revisions Page Contents Section 1. Features and Specifications Section 2. Installation and Configuration Section 3. Operation Section 4. Calibration Section 1. Features and Specifications Description Page Specifications Table 1.1 Specifications for XFR 1200 W Series Supply with RS-232 Interface Installed (7.5V to 40 V) Table 1.2 Specifications for XFR 1200 W Series Supply with RS-232 Interface Installed (60 V to 600 V) Table 1.3 Specifications for XFR 2800 W Series Supply with RS-232 Interface Installed (7.5V to 40 V) Table 1.4 Specifications for XFR 2800 W Series Supply with RS-232 Interface Installed (60 V to 600 V) Table 1.5 Specifications for XHR 1000 W Series Supply with RS-232 Interface Installed (7.5V to 60 V) Table 1.6 Specifications for XHR 1000 W Series Supply with RS-232 Interface Installed (100V to 600 V) Section 2. Installation and Configuration Figure 2.1 20 Power Supply Front Panel with RS-232 Interface Installed (1200 Watt Power Supply Shown) on page 34 Figure 2.2 RS-232 Interface Subplate (Located on Power Supply Rear Panel) Figure 2.3 RS-232 Interface PCB 22 Basic Setup Procedure Communications Page Page Remote/Local Operation Page Page RS-232 Connection Power Supply Settings Table 2.11 Power Supply Settings User Options and Settings Page User Signals Page Page Section 3. Operation Introduction RS-232 Operation Command Syntax Page Operation Command Syntax Table 3.1 Command Parameters Floating Point Number <float> Variables sent with command parameters are Table 3.2 Floating Point Numbers Command Strings Parameter Description Form Floating Number Definition Example ISET 2.0A; VSET 5V ISET 2.0A; VSET 5V Page Command Summary Table 3.3 Programming Commands Table 3.4 Query Commands Table 3.5 Calibration Commands Table 3.6 Status Commands Command Reference Table 3.7 Command Reference 51 Page page 27 Status, and Fault Registers on page 51 Remote/Local Operation on page 27 Status, and Fault Registers on page 51 Accumulated Status, Status, and Fault Registers on page 51 Registers on page 51 Page Accumulated Status, Status, and Fault Registers Table 3.8 Accumulated Status, Status, and Fault Registers Notes: Error Codes Table 3.9 Error Codes Troubleshooting Section 4. Calibration Voltage Mode Calibration V Page Current Mode Calibration V Page Over Voltage Protection (OVP) Calibration Page Xantrex Technology Inc.