Setup Menu Map, Page 35, Menu System, Part No | Xantrex Technology SW Series

MENU SYSTEM

SETUP MENU MAP

The SETUP MENU provides all the controls and settings needed when installing or adjusting the system. To access the SETUP MENU, press both the red ON/OFF MENU and green GEN MENU buttons on the Control Panel at the same time. To exit the SETUP MENU, press the red ON/OFF MENU button or press the down MENU HEADING button until you reach the USER MENU (menu headings 1-8).

MENU HEADINGS

Inverter Setup	Battery Charging	AC Inputs		Gen Auto Start		Gen starting		Auxiliary Relays
9	10		11	setup	12	details	13	R9 R10 R11	14

MENU ITEMS

Set Grid Usage

FLT SELL SLT LBX

Set Low battery cut out VDC 11.0

Set LBCO delay

minutes	10

Set Low battery
cut in VDC	13.0

Set High battery
cut out VDC	16.0

Set search
watts	48

Set search
spacing	59

Set Bulk
volts DC	14.4

Set Absorption
time h:m	02:00

Set Float
volts DC	13.4

Set Equalize
volts DC	14.4

Set Equalize
time h:m	02:00

Set Max Charge
amps AC	20

Set Temp Comp

LeadAcid NiCad

Set Grid (AC1)

amps AC	60

Set Gen (AC2)
amps AC	30

Set Input lower
limit VAC	108

Set Input upper
limit VAC	132

Set Load Start

amp AC	20

Set Load Start
delay min	5.0

Set Load Stop
delay min	5.0

Set 24 hr start
volts DC	12.3

Set 2 hr start
volts DC	11.8

Set 15 min start
volts DC	11.3

Read LBCO 30 sec
start VDC	11.0

Set Exercise
period days	30

Set Maximum run
time h:m	08:00

Set Max Run time to 0 to defeat.

Set Exercise to 0 to defeat.

See menu 9 to to set LBCO.

Set RY7 Function GlowStop Run

Set Gen warmup

seconds 60

Set Pre Crank

seconds 10

Set Max Cranking

seconds 10

Set Post Crank

seconds 30

Set Relay 9

volts DC	14.5

R9 Hysteresis
volts DC	01.0

Set Relay 10
volts DC	14.8

R10 Hysteresis
volts DC	01.0

Set Relay 11
volts DC	15.0

R11 Hysteresis
volts DC	01.0
Close on batt >
setpoint.
Open on	batt <

setpoint - Hys

Relays have 2 second delay on

Close, 0.1 sec delay on open

Bulk Charge

Low Battery

Battery Selling

Grid Usage Timer

Information file

End Setup Menu

Trigger Timer 15

Transfer (LBX) 16

battery

Set Start Bulk

Set Low Battery

Set Battery Sell

Start Charge

Batt temp comp

time

00:00

TransferVDC

11.3

volts DC

13.4

time

21:00

changes battery

To disable timer

Set Low battery

Set Max Sell

End Charge

voltage reading

set to 00:00

cut in VDC

13.0

amps AC

time

21:00

away from actual

If grid timer

See menu 9 to

After Start

HBCO resets at:

active set bulk

enable LBX mode.

enable SELL mode.

Charge time:

6v/48, 3v/24 and

time after start

Make sure LBX is

SELL mode

1.5v/12v under

charge time.

above LBCO volts.

charges battery.

HBCO.

In SLT mode don’t

FLT mode

LowBattTransfer

disable this

charges battery

used in LBX, FLT

timer. It is the

After End Charge

Modes only. Goes

daily chg time.

time:

back to battery

SELL mode sells

at LowBattCutIn

battery to AC1.

(aka LBCI).

FLT mode drops

For LBX mode set

AC1 and inverts

below LBCI so

Timer on when

charger won’t

start < > end;

cycle batteries

timer off when

up and down and

start = end

set LBCO below.

Sell and float modes use timer

SLT and LBX mode ignore timer

 2001 Xantrex Technology, Inc.	Telephone: 360/435-8826	SW Series Inverter/Charger
5916 - 195th Street N. E.	Fax: 360/435-2229	Part No. 2031-5
Arlington, WA 98223	www.traceengineering.com	Rev. C: February 2001

Xantrex Technology SW Series Setup Menu Map, Page 35, Menu System, Menu Headings, Menu Items

Models: SW Series

SETUP MENU MAP

Page