Troubleshooting Reference

 

Table 4-1Troubleshooting Reference

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3UREOHP

3RVVLEOH￿&DXVH

6ROXWLRQ

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

No output voltage. No

 

 

Turn the On/Standby switch on the inverter

 

 

 

 

 

 

The switch is in Standby ( )

 

 

indicator lights are

to On (

 

).

 

 

 

 

 

 

 

 

mode.

 

 

 

 

 

 

 

 

 

 

 

 

illuminated.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

No input power to the

Check the DC wiring to the inverter for

 

 

 

inverter.

loose connections, frayed wiring or an open

 

 

 

 

 

DC Disconnect.

 

 

 

DC fuse open (external)

Have a qualified service technician check

 

 

 

 

 

and replace the fuse.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

No output voltage. Inverter

Supplemental Circuit

Disconnect all equipment to reduce the

 

 

ON light is illuminated.

Protection button has tripped.

overload. Check the AC wiring and reset

 

 

 

 

 

the Supplemental Circuit Protection button.

 

 

 

GFCI has tripped.

Clear the ground fault, and reset the GFCI

 

 

 

 

 

by pressing the Reset button on the GFCI.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

No output voltage. Fault light

Inverter may be overloaded.

Disconnect all equipment connected to the

 

 

is illuminated.

 

 

inverter, and reset the inverter by turning

 

 

 

 

 

the On/Standby switch to Standby (

 

) and

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Battery voltage may be too

then to On (

 

).

 

 

 

 

 

 

 

 

 

 

 

 

 

The inverter will restart if the battery

 

 

 

high.

voltage drops below 14.5 volts DC.

 

 

 

Over temperature.

Allow the inverter to cool down. The

 

 

 

 

 

inverter will restart automatically.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

No output voltage. Low

Battery voltage is too low.

Recharge the battery to more than 12.6

 

 

Battery light is illuminated

 

 

volts DC. The inverter will restart

 

 

and alarm is on.

 

 

automatically.

 

 

 

Poor DC wiring.

Turn the inverter to Standby (

 

).

 

 

 

 

 

 

 

 

 

 

 

 

 

Disconnect the DC wiring. Use proper

 

 

 

 

 

wiring and ensure all connections are tight.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

975-0055-01-01

4–3

Page 57
Image 57
Xantrex Technology TS400 manual 1Troubleshooting Reference, 3UREOHP 3RVVLEOH&DXVH