Effects Parameters 137
Appendix: Parameter Lists
01V96i—Reference Manual
DYNA. PHASER

Two input, two output dynamically controlled

phaser.

REV+CHORUS

One input, two output reverb and chorus effects in

parallel.
REV->CHORUS

One input, two output reverb and chorus effects in

series.
REV+FLANGE

One input, two output reverb and flanger effects in

parallel.
Parameter Range Description
SOURCE INPUT, MIDI Control source: input signal or
MIDI Note On velocity
SENSE 0–100 Sensitivity
DIR. UP, DOWN Upward or downward fre-
quency change
DECAY 1
1. 6 ms–46.0 s (fs=44.1 kHz), 5 ms–42.3 s (fs=48 kHz), 3ms–23.0 s
(fs=88.2kHz), 3 ms–21.1 s (fs=96 kHz)
Decay speed
OFFSET 0–100 Lowest phase-shifted frequency
offset
FB.GAIN –99 to +99%
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feed-
back)
STAGE 2, 4, 6, 8, 10, 12,
14, 16 Number of phase shift stages
LSH F 21.2Hz–8.00kHz Low shelving filter frequency
LSH G –12.0 to +12.0 dB Low shelving filter gain
HSH F 50.0Hz–16.0 kHz High shelving filter frequency
HSH G –12.0 to +12.0 dB High shelving filter gain
Parameter Range Description
REV TIME 0.3–99.0 s Reverb time
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
HPF THRU,
21.2Hz–8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz–16.0 kHz,
THRU Low-pass filter cutoff frequency
REV/CHO 0–100% Reverb and chorus balance (0%
= all reverb, 100% = all chorus)
FREQ. 0.05–40.00 Hz Modulation speed
AM DEPTH 0–100% Amplitude modulation depth
PM DEPTH 0–100% Pitch modulation depth
MOD. DLY 0.0–500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF, ON Tempo parameter sync on/off
NOTE 1
1.
Used in conjunction with TEMPO
to determine FREQ.
Parameter Range Description
REV TIME 0.3–99.0 s Reverb time
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
HPF THRU,
21.2Hz–8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz–16.0 kHz,
THRU Low-pass filter cutoff frequency
REV.BAL 0–100%
Reverb and chorused reverb bal-
ance (0% = all chorused reverb,
100% = all reverb)
FREQ. 0.05–40.00 Hz Modulation speed
AM DEPTH 0–100% Amplitude modulation depth
PM DEPTH 0–100% Pitch modulation depth
MOD. DLY 0.0–500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF, ON Tempo parameter sync on/off
NOTE 1
1.
Used in conjunction with TEMPO
to determine FREQ.
Parameter Range Description
REV TIME 0.3–99.0 s Reverb time
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
HPF THRU,
21.2Hz–8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz–16.0 kHz,
THRU Low-pass filter cutoff frequency
REV/FLG 0–100% Reverb and flange balance (0% =
all reverb, 100% = all flange)
FREQ. 0.05–40.00 Hz Modulation speed
DEPTH 0–100% Modulation depth
MOD. DLY 0.0–500.0 ms Modulation delay time
FB. GAIN –99 to +99%
Feedback gain (plus values for
normal-phase feedback, minus
values for reverse-phase feed-
back)
WAVE Sine, Tri Modulation waveform
SYNC OFF, ON Tempo parameter sync on/off
NOTE 1
1.
Used in conjunction with TEMPO
to determine FREQ.