Yamaha 01V96i Bus Outs

Bus Outs 29

01V96i—Reference Manual

Bus Outs

Bus Outs

This chapter describes how to adjust the 01V96i’s Stereo Out

and Bus Out 1–8 parameters.

About Stereo Out

The Stereo Out section receives Input Channel and Bus Out

1–8 signals, mixes them into two channels, processes them

using on-board EQ, compressor, etc., then routes them to the

STEREO OUT and 2TR OUT connectors. The following dia-

gram illustrates the Stereo Out signal flow.

•INSERT

This section enables you to route the Stereo Out signals to

external devices via the on-board connectors or I/O card,

or insert internal effects processors.

•ATT (Attenuator)

This section enables you to attenuate or amplify the level

of signals to be input to the EQ. The attenuator prevents

post-EQ signals from clipping or corrects signal levels

that are too low.

• 4 BAND EQ (4-band equalizer)

This parametric EQ features four bands (HIGH,

HIGH-MID, LOW-MID, and LOW).

•COMP (Compressor)

This dynamics processor can be used as compressor,

expander, or limiter. The processor can be located

pre-EQ, pre-[STEREO] fader, or post-[STEREO] fader.

• ON (On/Off)

This button turns the Stereo Out on or off.

•LEVEL

The [STEREO] fader adjusts the Stereo Out output levels.

•Balance

This section enables you to adjust the level balance

between the L and R channels of the Stereo Out.

•OUTPUT DELAY (Output delay)

This section delays the output signals. It is mainly used to

fine-tune the signal timing.

• METER

This section enables you to switch the metering position

of signal levels that are displayed on the Meter page or by

the stereo meter to the right of the screen.

For more information on selecting the metering position,

refer to “Viewing the Level Meters” in the Owner’s Man-

ual (booklet).

Bus Out 1–8

The Bus Out 1–8 section mixes signals routed from Input

Channels to the specified buses, processes them using

on-board EQ, compressor, etc., then routes them to the spec-

ified output connectors or I/O card.

The following diagram illustrates the Bus Out signal flow.

•INSERT

•ATT (Attenuator)

• 4 BAND EQ (4-band equalizer)

•COMP (Compressor)

• ON (On/Off)

•LEVEL

•OUTPUT DELAY (Output delay)

• METER

The parameters and sections listed above are identical to

those for the Stereo Out. For more information, refer to

the explanation of the Stereo Out.

•Bus to Stereo

Bus Out 1–8 signals are also routed to the Stereo Bus. In

addition to the ON, LEVEL, and other parameters, you

can also set the Send Level, On/Off, Pan, and other

parameters.

OUTPUT PATCH

OUTPUT

DELAY

METER

ATT 4BAND

INSERT INSERT LEVEL

COMP

METER

(Gain Reduction)

BAL

INSERT

Same as stereo master L

METER

(Out Meter)

STEREO L

STEREO R

[STEREO OUT]

(+4dBu)

(-10dBV)

[2TR OUT]

Note: You can also patch the Stereo Out signals to other output

connectors or the I/O card by using the Patch | Out Patch pages.

Tip:

•You can also pair adjacent odd-even buses for stereo operation

(see page33).

•By default, Slot channels 1–8 and 9–16 and ADAT OUT chan-

nels 1–8 are patched to the Bus Out 1–8 outputs. However, you

can change this patching on the Patch | Out Patch page (see

page44).

OUTPUT PATCH

OUTPUT

DELAY

METER

ATT 4BAND

INSERT INSERT LEVEL

COMP

METER

(Gain Reduction)

INSERT

METER

(Out Meter)

STEREO L

STEREO R

BUS1

BUS2

BUS3

BUS4

BUS5

BUS6

BUS7

BUS8

PAN BUS to STEREO

LEVEL

BUS 1(...8)