144 Appendix: Parameter Lists
01V96i—Reference Manual
REV-X Hall, REV-X Room, REV-X Plate

This is a 2-in/2-out reverb algorithm. It provides

rich, high-density reverberation with a smooth

decay, and depth and spaciousness that will enhance

the original sound. You can choose one of three pro-

grams to suit the venue and your needs: REV-X Hall,

REV-X Room, and REV-X Plate.

Max 100

This is a 1-in/1-out phaser that emulates a vintage

effect that was manufactured only during the late

1970s.

Vintage Phaser

This is a 1-in/1-out phaser that offers an extremely

high level of freedom in creating phaser sounds,

without limiting itself to emulating any particular

model.

Parameter Range Description
REV TIME 0.32–32.14s
Specifies the duration of time
until the reverberation decays to
silence. Higher values produce
longer reverberation
INI.DLY 0.0–125.0ms
Specifies the time delay from
when the original sound is input
until reverberation begins.
Higher values produce a longer
delay before reverberation
begins
DECAY 0–53
Specifies the shape of the rever-
beration’s envelope. This value
will affect the characteristics of
the reverberation
ROOMSIZE 0–28
Specifies the size of the space.
Higher values simulate a broader
space. This value is linked with
the Reverb Time. Changing this
value will also change the Reverb
Time
DIFF. 0–10
Specifies the density and diffu-
sion of the reverberation. Higher
values will increase the density
and strengthen the sense of spa-
ciousness
HPF Thru–8.00 kHz
This is a filter that cuts the
low-frequency range of the
reverberation. The region below
the frequency specified here will
be cut. This filter does not affect
the original sound
LPF 1.00 kHz–Thru
This is a filter that cuts the
high-frequency range of the
reverberation. The region above
the frequency specified here will
be cut. This filter does not affect
the original sound
HI.RATIO 0.1–1.0
Adjusts the decay time of the
high-frequency reverberation.
This specifies the high-fre-
quency decay time as a propor-
tion of the Reverb Time
LO.RATIO 0.1–1.4
Adjusts the decay time of the
low-frequency reverberation.
This specifies the low-frequency
decay time as a proportion of
the Reverb Time
LO.FREQ. 22.0 Hz–18.0 kHz
Specifies the frequency on which
Lo Ratio is based. The region
below this frequency will be
affected by the Lo Ratio
Level
meter
Use the METER: [IN] [OUT]
switches to choose whether the
input level or output level will be
shown
MIX 0–100%
Adjusts the balance between the
original sound and the effect
sound.
Only the original sound will be
output if this value is 0%, and
only the effect sound will be out-
put if this value is 100%
Parameter Range Description
MODE 1, 2, 3, 4
Switches the sound quality
(tone). There are four types
available, each with differences
in modulation amplitude and in
the amount of feedback
SPEED SYNC,
0.100–10.000 Hz Adjusts the rate of modulation
Parameter Range Description
SPEED SYNC, 0.1–10.0 Hz Adjusts the rate of modulation
MANUAL 0.00–10.00 Adjusts the center frequency of
modulation
DEPTH 0.00–10.00 Adjusts the depth of modulation
FEEDBACK 0.00–10.00 Adjusts the amount of feedback
COLOR 0.00–10.00
This parameter is available for
certain combinations of MODE
and STAGE. It allows you to
fine-tune the tonal character
MODE 1, 2
Selects the type of circuit config-
uration being modeled. This will
affect the tonal character
STAGE 4, 6, 8, 10
Specifies the number of stages in
the circuit being modeled. This
will affect the tonal character