Manuals
/
Zap
/
Household Appliance
/
Garage Door Opener
Zap
815-RL installation instructions
Models:
815-RL
1
25
28
28
Download
28 pages
63.62 Kb
21
22
23
24
25
26
27
28
<
>
Install
Low Voltage Dc Motor Wiring
Next slide the Super-Driveassembly onto the door shaft and select a suitable hole in the torque arm to bolt it to the Super-Driveback plate using the spacer bush, which should pass through the lower slot in the Cover back. Pic 7 The Cover back will be secured later. The Torque Arm should be approximately at right angles to the Super-Driveassembly
Fault Finding Guide
Auto-Closetimer Programming
Remote Control Of The Light
Testing The Door Operation
Do Not Plug The Power Plug Into The
Page 25
Image 25
ZAP
800-R
– SAFETY WIRING CONNECTIONS – ZAP
PHOTO-EYES
!
"
"
20
Page 24
Page 26
Page 25
Image 25
Page 24
Page 26
Contents
FOR INSTALLATION ONLY BY QUALIFIED PERSONNEL
Model 815-RL Installation Instructions
JACKSHAFT MOTOR-CONTROL SYSTEM
RESIDENTIAL GARAGE DOORS
Page
IMPORTANT INSTALLATION INSTRUCTIONS
FOR INTERNAL INSTALLATION ONLY
READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS
To reduce the risk of Injury or death
Page
14/15
CONTENTS
MANUAL OVER RIDE model ZA0093
PRODUCT OVERVIEW
PLUG-INBEEPER MODULE model 850 OPTIONAL
MOTOR COVER KIT model ZA0094
RESIDENTIAL GARAGE DOORS
JACKSHAFT MOTOR-CONTROLSYSTEM
Model 815-RLInstallation Instructions
FITTING THE SUPER-DRIVE OPERATOR
PREPARATION
Next slide the Super-Driveassembly onto the door shaft and select a suitable hole in the torque arm to bolt it to the Super-Driveback plate using the spacer bush, which should pass through the lower slot in the Cover back. Pic 7 The Cover back will be secured later. The Torque Arm should be approximately at right angles to the Super-Driveassembly
FITTING THE MANUAL OVER-RIDELEVER MECHANISM
Mark the hole positions for the Manual Over-Ridelever on the door track or frame in a convenient position with the lever held in the horizontal position. Drill two M5 or 7/32nd of an inch size holes. Pic
FITTING THE CONTROL UNIT
LOW VOLTAGE DC MOTOR WIRING
FITTING THE MOTOR COVER KIT
DO NOT PLUG THE POWER PLUG INTO THE
CONNECTING THE MAIN A/C SUPPLY
7.The new supply wiring should be terminated to the GREEN connector block. The correct locations for the Live, Neutral and Ground wires are marked on the panel next to the GREEN socket. The new Black live wire should be terminated in the left hand terminal. The White neutral wire should be terminated in the center terminal and the Green ground wire should be terminated in the right hand terminal. See Pic 24, previous page. Note that alternative wire colors apply to UK and Europe
TESTING THE DOOR OPERATION
DOOR SPEED CHANGE POINT CALIBRATION
DOOR DIRECTION ASSESMENT
After the door has calibrated, note that the Acknowledge LED will momentarily flash and the optional beeper will sound periodically whilst the door is moving. Pic 39 overleaf
SAFETY CIRCUIT WIRING
12 VOLT TWO WIRE PHOTO-EYEWIRING
ACCESSORY RADIO RECEIVER WIRING
INTERLOCK CIRCUIT WIRING
PROGRAMMING
TRANSMITTER CODE PROGRAMMING
REMOTE CONTROL OF THE LIGHT
ZAP 800-RCONTROLLER WIRING
AUTO-CLOSETIMER PROGRAMMING
ACCESSORY RADIO – PULSE OPERATION
PULSE OPERATION WITH LIFT MASTER 412 HM RADIO
ZAP 800-RCONTROLLER WIRING –
#$ %$& ! & *+ ,& -*!& 0
4 ,!*.5
Page
Page
FAULT
FAULT FINDING GUIDE
REASON & REMEDY
100 Waterloo Boulevard Anglesey Business Park
ZAP CONTROLS UK
Cannock Staffordshire WS12 1NR United Kingdom
