Manuals
/
Zap
/
Household Appliance
/
Garage Door Opener
Zap
815-RL installation instructions
Models:
815-RL
1
26
28
28
Download
28 pages
63.62 Kb
21
22
23
24
25
26
27
28
<
>
Install
Low Voltage Dc Motor Wiring
Next slide the Super-Driveassembly onto the door shaft and select a suitable hole in the torque arm to bolt it to the Super-Driveback plate using the spacer bush, which should pass through the lower slot in the Cover back. Pic 7 The Cover back will be secured later. The Torque Arm should be approximately at right angles to the Super-Driveassembly
Fault Finding Guide
Auto-Closetimer Programming
Remote Control Of The Light
Testing The Door Operation
Do Not Plug The Power Plug Into The
Page 26
Image 26
ZAP
800-R
– SAFETY WIRING CONNECTIONS –
NON-ZAP
PHOTO EYES
21
Page 25
Page 27
Page 26
Image 26
Page 25
Page 27
Contents
JACKSHAFT MOTOR-CONTROL SYSTEM
Model 815-RL Installation Instructions
FOR INSTALLATION ONLY BY QUALIFIED PERSONNEL
RESIDENTIAL GARAGE DOORS
Page
READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS
FOR INTERNAL INSTALLATION ONLY
IMPORTANT INSTALLATION INSTRUCTIONS
To reduce the risk of Injury or death
Page
CONTENTS
14/15
PLUG-INBEEPER MODULE model 850 OPTIONAL
PRODUCT OVERVIEW
MANUAL OVER RIDE model ZA0093
MOTOR COVER KIT model ZA0094
Model 815-RLInstallation Instructions
JACKSHAFT MOTOR-CONTROLSYSTEM
RESIDENTIAL GARAGE DOORS
PREPARATION
FITTING THE SUPER-DRIVE OPERATOR
Next slide the Super-Driveassembly onto the door shaft and select a suitable hole in the torque arm to bolt it to the Super-Driveback plate using the spacer bush, which should pass through the lower slot in the Cover back. Pic 7 The Cover back will be secured later. The Torque Arm should be approximately at right angles to the Super-Driveassembly
FITTING THE MANUAL OVER-RIDELEVER MECHANISM
Mark the hole positions for the Manual Over-Ridelever on the door track or frame in a convenient position with the lever held in the horizontal position. Drill two M5 or 7/32nd of an inch size holes. Pic
LOW VOLTAGE DC MOTOR WIRING
FITTING THE CONTROL UNIT
FITTING THE MOTOR COVER KIT
CONNECTING THE MAIN A/C SUPPLY
DO NOT PLUG THE POWER PLUG INTO THE
7.The new supply wiring should be terminated to the GREEN connector block. The correct locations for the Live, Neutral and Ground wires are marked on the panel next to the GREEN socket. The new Black live wire should be terminated in the left hand terminal. The White neutral wire should be terminated in the center terminal and the Green ground wire should be terminated in the right hand terminal. See Pic 24, previous page. Note that alternative wire colors apply to UK and Europe
TESTING THE DOOR OPERATION
DOOR DIRECTION ASSESMENT
DOOR SPEED CHANGE POINT CALIBRATION
After the door has calibrated, note that the Acknowledge LED will momentarily flash and the optional beeper will sound periodically whilst the door is moving. Pic 39 overleaf
SAFETY CIRCUIT WIRING
12 VOLT TWO WIRE PHOTO-EYEWIRING
PROGRAMMING
INTERLOCK CIRCUIT WIRING
ACCESSORY RADIO RECEIVER WIRING
REMOTE CONTROL OF THE LIGHT
TRANSMITTER CODE PROGRAMMING
ACCESSORY RADIO – PULSE OPERATION
AUTO-CLOSETIMER PROGRAMMING
ZAP 800-RCONTROLLER WIRING
#$ %$& ! & *+ ,& -*!& 0
ZAP 800-RCONTROLLER WIRING –
PULSE OPERATION WITH LIFT MASTER 412 HM RADIO
4 ,!*.5
Page
Page
REASON & REMEDY
FAULT FINDING GUIDE
FAULT
Cannock Staffordshire WS12 1NR United Kingdom
ZAP CONTROLS UK
100 Waterloo Boulevard Anglesey Business Park
