Manuals / Zebra Technologies / Computer Equipment / Printer

Zebra Technologies TLP 3844-Z manual Parallel Interface, Pin No Description

Models: TLP 3844-Z

1 68

Download 68 pages 15.87 Kb

Page 58

Parallel Interface

The maximum current available through the interface port is not to exceed a total of 0.75 amps.

Pin No.	Description

1	NStrobe/Host Clk

2-9	Data Bits 1-8

10	nACK/PtrClk

11	Busy/Per Busy

12	PError/ACK Dat Req.

13	Select/Xflag

14	NAuto Fd/Host Busy

15	Not Used

16-17	Ground

18	+5 V @ 0.75 A Fused

19-30	Ground

31	nInit

32	NFault/nData Avail.

33-34	Not Used

35	+5 V throught 1.8 K Ohms Resistor

36	NSelectin/1284 active

50	980441-001 Rev. A

Image 58

Zebra Technologies TLP 3844-Z manual Parallel Interface, Pin No Description

Contents

Users Guide Thermal Printers980441-001 Rev. a Proprietary Statement Media and Ribbon BatteryShock Hazard Static DischargeContents Operation & Options Universal Serial Bus USB Connector 980441-001 Rev. a Introduction HelloWhat’s in the Box? Inspecting the Printer Opening the printerInspecting the Printer Closing the printer Related Documentation Reporting DamageGetting Started Modes of PrintingAttaching Power Supply Loading Roll Media Placing the Roll in the Media CompartmentAdjusting the Guides Install the Take-Up Core Install the Ribbon Supply RollLoading Ribbon Attach and Tighten the Ribbon Auto Calibration Feed Button Power SwitchOperator Controls Status LightPrinting a Test Printout Hooking Up the Printer and Computer Interface Cable RequirementsEthernet Interface Requirements USB Interface RequirementsParallel Interface Requirements Serial Interface RequirementsParallel Communications Communicating with the PrinterUniversal Serial Bus USB Communications Internal ZebraNet PrintServer Iitm CommunicationsSC Command Defaulting the Serial ParametersAdjusting the Print Darkness Adjusting the Print WidthAdjusting the Print Speed Operation & Options Thermal PrintingAdding a New Transfer Ribbon Replacing SuppliesReplacing a Partially Used Transfer Ribbon Printing in Peel-Mode Printing on Fan-Fold Media Using the Cutter Option 980441-001 Rev. a Maintenance CleaningPrint Head Considerations Cleaning Card ConsiderationsMedia Path Considerations Lubrication Platen ConsiderationsReplacing the Platen AssemblyRemoval Replacing the Print Head Thermal-Transfer TLP Model RemovalAssembly 980441-001 Rev. a Printer is not receiving power TroubleshootingResolutions Printer is on and in an idle statePrinter is receiving data Printer has failed its power on self test PostThere is a shortage of memory Either the media or ribbon is outPrint head is over temperature Print head is under temperatureFlash memory is not programmed No print on the label Print Quality ProblemsRibbon sensor settings did not print Printed image does not look rightLabel format was sent to, but not recognized by, the printer Manual Calibration Printing a Configuration Label Troubleshooting TestsRecalibration Resetting the Factory Default Values Communications DiagnosticsPower Off Mode Communications Diagnostics Mode Feed Button Modes980441-001 Rev. a Printing Specifications SpecificationsPhysical Specifications AppendixMedia Specifications Ribbon Specifications for TLP modelFont/Code Specifications Zebra Programming Language ZPLAgency Approvals OptionsUniversal Serial Bus USB Connector InterfacesParallel Interface Pin No DescriptionLooking into the Printer’s RJ-45 Modular Connector ZebraNet PrintServer II for Ethernet NetworksSerial RS-232 Connector Connecting the Printer to a DTE Device 980441-001 Rev. a Index Cable calibrationQuality problems Voltage Page