Battery, Shock Hazard | Zebra Technologies TLP 3844-Z guide

Battery

The main printed circuit board assembly includes a three-volt lithium battery.

CAUTION—Risk of explosion if battery is replaced with an incorrect type.

Note—Recycle batteries according to local your guidelines and regulations.

Shock Hazard

The printer and power supply should never be operated in a location where either one can get wet. Personal injury could result.

Media and Ribbon

Always use high-quality, approved labels, tags and ribbons. If adhesive backed labels are used that DO NOT lay flat on the backing liner, the exposed edges may stick to the label guides and rollers inside the printer, causing the label to peel off from the liner and jam the printer. Permanent damage to the print head may result if a non-approved ribbon is used as it may be wound incorrectly for the printer or contain chemicals corrosive to the print head. Approved supplies can be ordered from your dealer.

If labels or ribbon run out while printing, DO NOT turn the power switch OFF (0) while reloading or data loss may result. After loading new supplies, press the feed button to resume printing.

Static Discharge

The discharge of electrostatic energy that accumulates on the surface of the human body or other surfaces can damage or destroy the print head or electronic components used in this device. DO NOT TOUCH the print head or the electronic components under the top cover.

Thermal Printing

The print head becomes hot while printing. To protect from damaging the print head and risk of personal injury, avoid touching the print head. Use only the cleaning pen to perform maintenance.

iv	980441-001 Rev. A

Image 4

Zebra Technologies TLP 3844-Z manual Battery, Shock Hazard, Media and Ribbon, Static Discharge, Thermal Printing

Contents

Users Guide Thermal Printers 980441-001 Rev. a Proprietary Statement Battery Shock HazardMedia and Ribbon Static Discharge Contents Operation & Options Universal Serial Bus USB Connector 980441-001 Rev. a Introduction Hello What’s in the Box? Inspecting the Printer Opening the printer Inspecting the Printer Closing the printer Related Documentation Reporting Damage Getting Started Modes of Printing Attaching Power Supply Loading Roll Media Placing the Roll in the Media Compartment Adjusting the Guides Install the Take-Up Core Install the Ribbon Supply RollLoading Ribbon Attach and Tighten the Ribbon Auto Calibration Power Switch Operator ControlsFeed Button Status Light Printing a Test Printout Hooking Up the Printer and Computer Interface Cable Requirements USB Interface Requirements Parallel Interface RequirementsEthernet Interface Requirements Serial Interface Requirements Communicating with the Printer Universal Serial Bus USB CommunicationsParallel Communications Internal ZebraNet PrintServer Iitm Communications SC Command Defaulting the Serial Parameters Adjusting the Print Darkness Adjusting the Print WidthAdjusting the Print Speed Operation & Options Thermal Printing Adding a New Transfer Ribbon Replacing SuppliesReplacing a Partially Used Transfer Ribbon Printing in Peel-Mode Printing on Fan-Fold Media Using the Cutter Option 980441-001 Rev. a Maintenance Cleaning Print Head Considerations Cleaning Card ConsiderationsMedia Path Considerations Lubrication Platen Considerations Replacing the Platen AssemblyRemoval Replacing the Print Head Thermal-Transfer TLP Model Removal Assembly 980441-001 Rev. a Troubleshooting ResolutionsPrinter is not receiving power Printer is on and in an idle state Printer has failed its power on self test Post There is a shortage of memoryPrinter is receiving data Either the media or ribbon is out Print head is over temperature Print head is under temperatureFlash memory is not programmed Print Quality Problems Ribbon sensor settings did not printNo print on the label Printed image does not look right Label format was sent to, but not recognized by, the printer Manual Calibration Printing a Configuration Label Troubleshooting TestsRecalibration Resetting the Factory Default Values Communications Diagnostics Power Off Mode Communications Diagnostics Mode Feed Button Modes 980441-001 Rev. a Specifications Physical SpecificationsPrinting Specifications Appendix Media Specifications Ribbon Specifications for TLP model Font/Code Specifications Zebra Programming Language ZPL Agency Approvals Options Universal Serial Bus USB Connector Interfaces Parallel Interface Pin No Description Looking into the Printer’s RJ-45 Modular Connector ZebraNet PrintServer II for Ethernet Networks Serial RS-232 Connector Connecting the Printer to a DTE Device 980441-001 Rev. a Index Cable calibration Quality problems Voltage Page