Agency Approvals, Options | Zebra Technologies TLP 3844-Z instruction

Agency Approvals

The thermal-transfer printer model TLP 3844-Z, manufactured by Zebra Technologies Corporation, complies with the applicable requirements:

SUBJECT	AGENCY	COUNTRIES	STANDARDS

Emissions	FCC	United States	Part 15, Subpart B

	VCCI	Japan	V-3/93.01

	C-Tick	Australia	C-Tick
		New Zealand

	CE	European	EN55022 Class B
		Union

Susceptibility	CE	European	EN61000-3-2, EN61000-3-3,
and Immunity		Union	EN55024

Safety	UL	United States	UL60950

	C-UL	Canada	CSA/CAN C22-2 #950-M89

	CB Scheme	Multiple	EN60950:1991;
			amendments 1, 2, 3 and 4
			EN60950:1992;
			amendments 1, 2, 3, 4 and 11

	IRAM	Argentina	EN60950

	NOM	Mexico	019-SCFI-1998

Options

TLP 3844-Z

✔ZebraNet PrintServer II (internal ethernet interface)

✔Maximum 12 MB total memory

✔Asian fonts

✔Real-Time Clock

✔Dispenser for “peel-off mode”

✔Cutter

All specifications are subject to change without notice.

48	980441-001 Rev. A

Image 56

Zebra Technologies TLP 3844-Z manual Agency Approvals, Options

Contents

Users Guide Thermal Printers 980441-001 Rev. a Proprietary Statement Battery Shock HazardMedia and Ribbon Static Discharge Contents Operation & Options Universal Serial Bus USB Connector 980441-001 Rev. a Introduction Hello What’s in the Box? Inspecting the Printer Opening the printer Inspecting the Printer Closing the printer Related Documentation Reporting Damage Getting Started Modes of Printing Attaching Power Supply Loading Roll Media Placing the Roll in the Media Compartment Adjusting the Guides Loading Ribbon Install the Ribbon Supply RollInstall the Take-Up Core Attach and Tighten the Ribbon Auto Calibration Power Switch Operator ControlsFeed Button Status Light Printing a Test Printout Hooking Up the Printer and Computer Interface Cable Requirements USB Interface Requirements Parallel Interface RequirementsEthernet Interface Requirements Serial Interface Requirements Communicating with the Printer Universal Serial Bus USB CommunicationsParallel Communications Internal ZebraNet PrintServer Iitm Communications SC Command Defaulting the Serial Parameters Adjusting the Print Speed Adjusting the Print WidthAdjusting the Print Darkness Operation & Options Thermal Printing Replacing a Partially Used Transfer Ribbon Replacing SuppliesAdding a New Transfer Ribbon Printing in Peel-Mode Printing on Fan-Fold Media Using the Cutter Option 980441-001 Rev. a Maintenance Cleaning Media Path Considerations Cleaning Card ConsiderationsPrint Head Considerations Lubrication Platen Considerations Removal AssemblyReplacing the Platen Replacing the Print Head Thermal-Transfer TLP Model Removal Assembly 980441-001 Rev. a Troubleshooting ResolutionsPrinter is not receiving power Printer is on and in an idle state Printer has failed its power on self test Post There is a shortage of memoryPrinter is receiving data Either the media or ribbon is out Flash memory is not programmed Print head is under temperaturePrint head is over temperature Print Quality Problems Ribbon sensor settings did not printNo print on the label Printed image does not look right Label format was sent to, but not recognized by, the printer Manual Calibration Recalibration Troubleshooting TestsPrinting a Configuration Label Resetting the Factory Default Values Communications Diagnostics Power Off Mode Communications Diagnostics Mode Feed Button Modes 980441-001 Rev. a Specifications Physical SpecificationsPrinting Specifications Appendix Media Specifications Ribbon Specifications for TLP model Font/Code Specifications Zebra Programming Language ZPL Agency Approvals Options Universal Serial Bus USB Connector Interfaces Parallel Interface Pin No Description Looking into the Printer’s RJ-45 Modular Connector ZebraNet PrintServer II for Ethernet Networks Serial RS-232 Connector Connecting the Printer to a DTE Device 980441-001 Rev. a Index Cable calibration Quality problems Voltage Page