Zebra Technologies TLP 3844-Z instruction

Connecting the Printer to a DTE Device

DB-25S				DB-9P
Connector			Connector
to DTE Device (PC)				to Printer
	TXD			DCD
2						1
	RXD			RXD
3						2
	RTS			TXD
4						3
	CTS			DTR
5						4
	DSR			GND
6						5
	GND			DSR
7						6
	DCD			RTS
8						7
	DTR			CTS
20						8
22						9

DB-9S				DB-9P
Connector			Connector
to DTE Device (PC)			to Printer
	DCD			DCD
1					1
	RXD			RXD
2					2
	TXD			TXD
3					3
	DTR			DTR
4					4
	GND			GND
5					5
	DSR			DSR
6					6
	RTS			RTS
7					7
	CTS			CTS
8					8

9					9

Connecting the Printer to a DCE Device

	DB-25S		DB-9P
	Connector		Connector
	to DCE Device		to Printer
		RXD	DCD
	2			1
		TXD	RXD
	3			2
		CTS	TXD
	4			3
		RTS	DTR
	5			4
		DTR	GND
	6			5
		GND	DSR
	7			6
		DCD	RTS
	8			7
		DSR	CTS
	20			8
	22			9

	DB-9S		DB-9P
	Connector		Connector
	to DCE Device		to Printer
		DCD	DCD
	1			1
		TXD	RXD
	2			2
		RXD	TXD
	3			3
		DSR	DTR
	4			4
		GND	GND
	5			5
		DTR	DSR
	6			6
		CTS	RTS
	7			7
		RTS	CTS
	8			8

	9			9

980441-001 Rev. A

53

Image 61

Zebra Technologies TLP 3844-Z manual Connecting the Printer to a DTE Device

Contents

Thermal Printers Users Guide 980441-001 Rev. a Proprietary Statement Shock Hazard BatteryMedia and Ribbon Static Discharge Contents Operation & Options Universal Serial Bus USB Connector 980441-001 Rev. a Hello Introduction What’s in the Box? Opening the printer Inspecting the Printer Inspecting the Printer Closing the printer Reporting Damage Related Documentation Modes of Printing Getting Started Attaching Power Supply Placing the Roll in the Media Compartment Loading Roll Media Adjusting the Guides Install the Take-Up Core Install the Ribbon Supply RollLoading Ribbon Attach and Tighten the Ribbon Auto Calibration Operator Controls Power SwitchFeed Button Status Light Printing a Test Printout Interface Cable Requirements Hooking Up the Printer and Computer Parallel Interface Requirements USB Interface RequirementsEthernet Interface Requirements Serial Interface Requirements Universal Serial Bus USB Communications Communicating with the PrinterParallel Communications Internal ZebraNet PrintServer Iitm Communications Defaulting the Serial Parameters SC Command Adjusting the Print Darkness Adjusting the Print WidthAdjusting the Print Speed Thermal Printing Operation & Options Adding a New Transfer Ribbon Replacing SuppliesReplacing a Partially Used Transfer Ribbon Printing in Peel-Mode Printing on Fan-Fold Media Using the Cutter Option 980441-001 Rev. a Cleaning Maintenance Print Head Considerations Cleaning Card ConsiderationsMedia Path Considerations Platen Considerations Lubrication Replacing the Platen AssemblyRemoval Replacing the Print Head Removal Thermal-Transfer TLP Model Assembly 980441-001 Rev. a Resolutions TroubleshootingPrinter is not receiving power Printer is on and in an idle state There is a shortage of memory Printer has failed its power on self test PostPrinter is receiving data Either the media or ribbon is out Print head is over temperature Print head is under temperatureFlash memory is not programmed Ribbon sensor settings did not print Print Quality ProblemsNo print on the label Printed image does not look right Label format was sent to, but not recognized by, the printer Manual Calibration Printing a Configuration Label Troubleshooting TestsRecalibration Communications Diagnostics Resetting the Factory Default Values Feed Button Modes Power Off Mode Communications Diagnostics Mode 980441-001 Rev. a Physical Specifications SpecificationsPrinting Specifications Appendix Ribbon Specifications for TLP model Media Specifications Zebra Programming Language ZPL Font/Code Specifications Options Agency Approvals Interfaces Universal Serial Bus USB Connector Pin No Description Parallel Interface ZebraNet PrintServer II for Ethernet Networks Looking into the Printer’s RJ-45 Modular Connector Serial RS-232 Connector Connecting the Printer to a DTE Device 980441-001 Rev. a Cable calibration Index Quality problems Voltage Page