Manuals / Zonet Technology / Computer Equipment / Network Router

Zonet Technology ZSR0104C Series user manual D. PPTP Connection

Models: ZSR0104C Series

1 63

Page 21

b.Idle Time field: If the Idle Time was specified with non-zero number, ZSR0104C SERIES router disconnects the PPPoE session after there was no data traffic on WAN interface within the specified “Idle Time” minutes.

c.Auto-reconnectfield: Once there is any outgoing data traffic, the router automatically re-establishes the PPPoE session.

D. PPTP Connection

If Internet access is through the PPTP, please click the selection button of the “PPTP”. Then click “Next” button.

PPTP is a common type of Internet access provided by many Internet Service Providers. It requires you to enter the User Name, Password, Server IP Address, My IP Address, My Subnet Mask and Connection ID to obtain authentication. Additional two optional fields might be assigned value by user:

Page 14

Page 21

Image 21

Zonet Technology ZSR0104C Series user manual D. PPTP Connection

Contents

Page ZSR0104C Series Broadband Switch Router User ManualFCC Interference Statement The Specifications of ZSR0104C Series Chapter 3 Install Your ZSR0104C SERIES Table of ContentsChapter 1 Introduction Chapter 2 Get to Know The HardwareChapter 4 Use Your ZSR0104C SERIES Chapter 5 Advanced Setup of ZSR0104C SERIES6.2 Forget Password? Appendix AA.1 Disable Web Proxy A.2 Verify IP SettingsAppendix C Terminology Appendix B Common Port NumbersAppendix D Technical Support D.1 Hardware Problem1.2 Physical Features of ZSR0104C SERIES 1.1 The ZSR0104C SERIES Broadband Switch Router1.3 Non-Physical Features of ZSR0104C SERIES Chapter 1 Introduction‧ Dynamic DNS ‧ Firewall‧ Virtual Server Port Forwarding ‧ VPN Pass-Through1.5 Installation Requirements 1.4 Package Checklist1.6 About this User’s Manual ‧ Web-Based SetupChapter 5, Configure Your ZSR0104C SERIES Chapter 3, Install Your ZSR0104C SERIESOrganization of This User’s Manual Chapter 1, Introduction Chapter 2, Get to Know the HardwareChapter 2 Get to Know The Hardware 2.1 LED IndicatorsDevice Indicators LAN and WAN Indicators2.2 Back Panel 3. Reset Button1. Local LAN Ports 2. Internet WAN Port3.2 Connect Ethernet Hub/Switch to ZSR0104C SERIES Chapter 3 Install Your ZSR0104C SERIES3.3 Connect Wireless Access Point to ZSR0104C SERIES 4. Power Connector4.2 Wizard Setup 3.5 Power up ZSR0104C SERIESChapter 4 Use Your ZSR0104C SERIES 4.1 Check the Web ProxyAdministration in Chapter 5 Configure Your ZSR0104C SERIES Page Figure 4A. Cable Modem Connection B. Fixed-IP xDSL Connection C. PPP over Ethernet PPPoE Connection D. PPTP Connection a. 10.x.x.x with subnet mask 255.0.0.0 x must be in range 0 to Figure 4b. 172.x.x.x with subnet mask 255.255.0.0 x must be in range 0 to Figure 4 PageChapter 5 Advanced Setup of ZSR0104C SERIES 4.3 WAN Setup Complete5.1 Start from Advanced Setting 5.2 System 5.4 Administration 5.3 TimeThe default Time Server IP Address is 198.123.30.132 And WAN Side Administration Change Administrator’s User Name and PasswordPre-requirements 5.5 Firmware UpgradeStep 3. Click the “Apply” icon from the firmware upgrade page After clicking the “Apply” button, will appear the confirmation pagePage 5.6 Reset 5.7 Dynamic DNS Domain Name System Page Step 1. Select DDNS service provider1. DHCP Definition 5.8 DHCP Server2. DHCP Server in LAN A. Auto-Remember4. Static IP Assign 3. DHCP Client in LANB. The Pool Range of Assigned IP Address C. The DHCP IP Address Lease Time5.9 Virtual Server Port Forwarding 5. DHCP Client ListConfigure TCP/IP in Your PC Page 1. DMZ Host Configuration 5.10 FirewallA. Local DMZ Host B. Public DMZ Host 2. Anti PING and TCP/UDP Echo Attack 4. Port Filter 3. URL FilterA. Disable B. Blocking the following portA. Disable 5. MAC FilterPlease refer to Appendix B Common Port Numbers B. Blocking the following Mac6. IP Filter 6.1 TroubleshootingA. Disable B. Blocking the following IP2. Failed Connection between ZSR0104C SERIES and Client PC 1. Router’s Hardware Failure6.2 Forget Passwords? 3. Failed Connection on ZSR0104C SERIES WAN Side4. DNS Domain Name System Failure Appendix A A.1 Disable Web Proxy1. For Windows 95 / 98 / ME / 2000 /NT C. A. Internet ExplorerFigure A-23 Page Figure A-22D. B. Netscape Figure A-24Figure A-25 Page E. A. Internet Explorer 2. For Windows XPFigure A-29 Page Figure A-28Figure A-30 F. B. NetscapeStep 2. Choose Proxies under the advanced item. Figure A-31 Figure A-31 Page4. For Unix/Linux 3. For MACG. A. Explorer H. B. NetscapeA.2 Verify IP Settings 1. For Windows 95 / 98 / MEI. A. Netscape Step 2. Run the WINIPCFG command. Figure A-34 Figure A-34 Figure A-35Figure A-36 Figure A-36 Page Step 2. Please enter command and press the OK button. Figure A-38 2. For Windows 2000 /NTStep 1. Go through the path “Start→Run.”Figure A-37 Figure A-37 Figure A-38 PageFigure A-40 Page Figure A-39Step 2. Enter command and press the OK button. Figure A-42 3. For Windows XPFigure A-41 Figure A-424. For Mac 5. For Unix/Linux Appendix B Common Port Numbers Service NamePort Number ‧ Boot Appendix C Terminology‧ Browser ‧ Cable Modem‧ Firewall ‧ Infrastructure Mode‧ Firmware ‧ Gateway‧ MSN Messenger ‧ IP Address‧ NetMeeting ‧ Port‧ Switch ‧ RJ-45 Connector‧ Router ‧ ServerD.3 Installation/Application Problem D.1 Hardware ProblemAppendix D Technical Support D.2 Software Download