| 
 | 
 | Chapter 5 WAN Setup | 
| 
 | Table 10 WAN > Internet Connection: Advanced Setup (continued) | |
| 
 | LABEL | DESCRIPTION | 
| 
 | PPPoE | This field is available when you select PPPoE encapsulation. | 
| 
 | Passthrough | 
 | 
| 
 | (PPPoE | In addition to the ZyXEL Device's  | 
| 
 | encapsulati | PPPoE pass through to allow up to ten hosts on the LAN to use PPPoE | 
| 
 | on only) | |
| 
 | client software on their computers to connect to the ISP via the ZyXEL | |
| 
 | 
 | |
| 
 | 
 | Device. Each host can have a separate account and a public WAN IP | 
| 
 | 
 | address. | 
| 
 | 
 | PPPoE pass through is an alternative to NAT for application where NAT is | 
| 
 | 
 | not appropriate. | 
| 
 | 
 | Disable PPPoE pass through if you do not need to allow hosts on the LAN | 
| 
 | 
 | to use PPPoE client software on their computers to connect to the ISP. | 
| 
 | 
 | 
 | 
| 
 | IP Filter | This section is not available when you configure the ZyXEL Device to be | 
| 
 | 
 | in bridge mode. | 
| 
 | 
 | 
 | 
| 
 | IP Filter | Select this option to enable IP filtering on this connection. | 
| 
 | Active | 
 | 
| 
 | 
 | 
 | 
| 
 | VLAN | 
 | 
| 
 | 
 | 
 | 
| 
 | VLAN Active | Select this option to enable VLAN multiplexing of multiple protocols over | 
| 
 | 
 | a single virtual circuit. You need to assign a VLAN ID and priority level to | 
| 
 | 
 | traffic through each WAN connection. All WAN connections share one | 
| 
 | 
 | MAC address. This allows the backbone switch to classify and service | 
| 
 | 
 | traffic based on the VLAN tag, instead of the MAC address. | 
| 
 | 
 | Otherwise, disable VLAN multiplexing and each WAN connection has its | 
| 
 | 
 | own MAC address. | 
| 
 | 
 | Note: This field is only configurable for the first WAN connection. | 
| 
 | 
 | When you change the setting here, all existing WAN | 
| 
 | 
 | connections will be removed except for the first WAN | 
| 
 | 
 | connection. | 
| 
 | 
 | 
 | 
| 
 | VLAN ID | Enter a VLAN ID number for traffic that goes through this connection. | 
| 
 | 
 | 
 | 
| 
 | Priority | Enter a priority level for traffic that goes through this connection. | 
| 
 | 
 | 
 | 
| 
 | Back | Click this to return to the previous screen. | 
| 
 | 
 | 
 | 
| 
 | Apply | Click this to save the changes. | 
| 
 | 
 | 
 | 
| 
 | Reset | Click this to restore your  | 
| 
 | 
 | 
 | 
5.5 The More Connections Screen
The ZyXEL Device allows you to configure more than one Internet access connection. To configure additional Internet access connections click Network > WAN > More Connections. The screen differs by the encapsulation you select.
| 
 | 57 | 
| 
 | 
 |