Craftsman 580.6722 owner manual HOW to USE Your Pressure Washer, To Start Your Pressure Washer

Page 8

4 Provideproperwatersupply(notto exceed100°F)

5.Besureto read"SafetyRules"and"Operation" sectionsbeforeusingpressurewasher.

6.If startingunitafterstorage,see"Storage"section onpage15.

HOW TO USE YOUR PRESSURE WASHER

If you have any problems operating your pressure washer, please call the pressure washer helpline at 1-800-222-3136

To Start Your Pressure Washer

To start your engine-powered pressure washer for the first time, follow these instructions step-by-step. This starting information also applies whenever you start the engine after you have let the pressure washer sit idle for at least a day.

1.Place pressure washer near an outside water source capable of supplying water at a flow rate greater than 3.0 gallons per minute and no less than 20 PSI at pressure washer end of garden hose.

2.Check that high pressure hose is tightly connected

to spray gun and pump. See "Assembling Your Pressure Washer _ for illustrations.

. Make sure unit is in a level position.

4.Connect garden hose to water inlet on pressure washer pump. Turn ON water.

CAUTION

Damage to equipment will result from failure to follow this instruction,

5.Squeeze trigger on gun to purge pump system of air and impurities.

. Attach nozzle extension to spray gun. Tighten by hand.

\\

\

7.Position nozzle in low pressure mode (slide nozzle forward) and squeeze trigger on spray gun to relieve pressure caused by turning ON water. Water will flow out of gun in a thin stream. Continue to hold trigger until there is a steady stream of water and no air remains in system. Release trigger.

8 Engage safety latch to spray gun trigger

_SafetyLatch

. Move throttle lever to "Fast" position, shown here as a rabbit.

FastStop

f

Throttle

Lever in

STOP

position

NOTE: For a warm engine, be sure the throttle lever is in the "Fast" position.

To start the engine for the very first time:

10.Make sure throttle lever is in "Fast" position (indicated on the engine as a rabbit).

11.Push primer bulb firmly 5 times, waiting 2 seconds between each push.

To start engine thereafter:

10.Make sure throttle lever is in "Fast" position (indicated on the engine as a rabbit).

11.Press primer bulb firmly 3 times, waiting

2 seconds between each push. For a warm engine, DO NOT press primer bulb.

12.Grasp starter grip handle and pull slowly until you feel some resistance. Then pull rapidly to start

engine.

13.Return starter grip handle slowly. DO NOT let rope "snap back" against starter.

ACAUTION

Squeeze trigger on spray gun each time recoil starter is pulled and engine fails to start.

CAUTION

Always use handle to lift equipment,

NEVER pull on hoses to move equipment,

NOTE: Always keep the throttle lever in the "Fast" position when operating the pressure washer.

8

Image 8
Contents Hours Mon. FrL 8 a.m. to 5 p.m. CT HorsepowerSears Canada, Inc Hazard Symbols and Meanings Umited ONE Year Warranty on Craftsman Pressure WasherTurn pressure washer OFF and let it cool at least Engine exhaust from this product containsChemicals known to the State of California to cause Cancer, b rth defects, or other reproduct ve harmPage Know Your Pressure Washer Throttle ControlExtension with Turbo Nozzle -- The turbo nozzle Fuel CapRemove Pressure Washer from Carton Assembling Your Pressure WasherReview the unit to ensure you have performed all Checklist Before Starting EngineConnect Hose and Water Supply to Pump To start the engine for the very first time HOW to USE Your Pressure WasherTo Start Your Pressure Washer Using the Turbo Nozzle How to Stop Your Pressure WasherHow To Use the Adjustable Nozzle For Rinsing Pressure Washer RinsingTo apply detergent, follow these steps Product Specifications Pressure Washer MaintenanceOwners Responsibilities General RecommendationsNozzle Maintenance Check Gun and Nozzle ExtensionCheck In-Line Filter Purge Pump of Air and ContaminantsChanging Oil Engine MaintenancePump Maintenance Service Air Cleaner After Each USEGeneral Winter StorageLong Term Storage Protect Fuel SystemCorrection Ii!iliiiliiiii!iiiiii!iiiiiiiiiiiiiiiii 23139GS DescriptionPi6ce no Description Huile Description PartPifce no Description 459 6891210 597g 1211190 1630Description Owners Warranty Responsibilities Sears Emission Control Defects Warranty ProvisionsMaintenance Length of CoverageDachat Symboles de Danger et MoyensSears Canada, Inc Avertissemeni AvertissementAVERTISSEMEN1ATTENTION AVERTISSEMEN1Lre Rallonge de buseEt jaug InjectionFixez le Porte-Accessoires DI Baller LE Nettoyeur a Haute Pression DU CartonContenu DU Carton Assemblage DU Nettoyeur a Haute PressionAjouter de lEssence Raccorder le Tuyau et la Source Deau & la PompeComment Utiliser Votre Nettoyeur .&.HAUTE Pression Liste de Vdfications Avant de Dmarrer le MoteurMettre Votre Nettoyeur & Haute Pression en Marche Pour dmarrer Ie moteur pour la premi6re foisComment Arrter Metre Nettoyeur & Haute Pression Comment Utiliser les Gicleurs RdglablesUtilisation de la Turbo-Lance Gicleur en event pourAppliquer des Produits Ddtergents avec le Gicleur Rdglable Rincer le Nettoyeur & Haute PressionUSt6me de Refroidissement Automatique rpression Thermique Pour appliquer des produits detergents, procedez comma suitRecommandations General Responsabilites DU ProprietaireAvertiss Vidanger la pompe selon Ia procedure suivante Entretien DU MoteurEntretien de la Pompe Changement dhuilePour fairo Ientretien du filtre & air, procedez comme suit Apres Chaque UtilisationEntretien du filtre & air GI NI Raliti S Entreposage Pour LhiverEntreposage a Long Terme Autres DirectivesLe dtorgent ne se mlange pss avec le jet CorrectionResponsabilit6s de la garantie du propriJtaire LE-FOYER