Zenoah HT2200 manual Handling Fuel, Refill after cooling the engine, Transportation

Page 16

English

5. For safe operation

3.When replacing the cutting attachment or any other part, or when replacing the oil or any lubricant, always be sure to use only RedMax products or products which have been certified by RedMax for use with the RedMax product.

4.In the event that any part must be replaced or any maintenance or repair work not described in this manual must be performed, please contact a representative from the store nearest RedMax authorized servicing dealer for assistance.

5.Do not use any accessory or attachment other than those bearing the RedMax mark and recommended for the unit.

6.Under no circumstances should you ever take apart the product or alter it in any way. Doing so might result in the product becoming damaged during operation or the product becoming unable to operate properly.

HANDLING FUEL

1.The engine of the RedMax product is designed to run on a mixed fuel, which contains highly flammable gasoline. Never store cans of fuel or refill the tank of the unit in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel.

2.Never smoke while operating the unit or refilling its fuel tank.

3.When refilling the tank, always turn off the engine and allow it to cool down. Take a careful look around to make sure that there are no sparks or open flames anywhere nearby before refueling.

(1) Refill after cooling the engine.

4.Wipe spilled fuel completely using a dry rag if any fuel spillage occurs during refueling.

5.After refueling, screw the fuel cap back tightly onto the fuel tank and then carry the unit to a spot 3 m or more away from where it was refueled before turning on the engine.

6.Do not inhale fuel fumes as they are toxic.

TRANSPORTATION

1.When hand-carrying the product, cover over the cutting part if necessary, lift up the product and carry it paying attention to the blade.

2.Never transport the product over rough roads over long distances by vehicle without removing all fuel from the fuel tank. If doing so, fuel might leak from the tank during transport.

16

Image 16
Contents HT2200 CHT2200 Contents Tables des matieres Contenido Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOIAdvertencias Contenidas EN EL Manual Parts location SpecificationsModel HT2200 CHT2200 Emplacement des pieces Situación de las piezas Fiche techniqueEspecificaciohes Modelo HT2200 CHT2200Symbols on the machine Emplacement PosiciónWorking Condition For safe operationWorking Circumstance Consignes de securite Instrucciones de seguridad Conditions DE TravailCondición DE Trabajo Circunstancias DE TrabajoWorking Plan Before Starting the EnginePlan DE Travail Plan DE TrabajoAvant DE Mettre LE Moteur EN Marche Antes DE Arrancar LA MáquinaStarting the Engine Using the ProductCut only materials recommended by Demarrage DU Moteur Utilisation DE LA MachineArranque DE LA Máquina Empleo DEL ProductoMaintenance If Someone ComesConsignes de securite Instrucciones de seguridad SI QUELQU’UN S’APPROCHEEntretien SI SE Acerca AlguienRefill after cooling the engine Handling FuelTransportation Manipulation DU Carburant TransportManejo DEL Combustible Llenar una vez que el motor se haya enfriadoSet up Blade Washer Keep LooseBolt Plate Nut Corrugate tube 2 Tie band Throttle cable 4 Throttle leverAssemblage Montaje SE6 SE7 SE8 Assemblage Montaje Fuel When using RedMax/ZENOAH genuine oilRecommended Mixing Ratio Gasoline 50OIL Rapport DE Melange Recommande Essence 50 Huile Carburant CombustibleLors de l’utilisation de la véritable huile RedMax/ZENOAH Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteHOW to MIX Fuel Fueling the UnitRemplissage DU Reservoir Comment Obtenir UN BON Melange Como Mezclar EL CombustibleAbastecimiento DE LA Unidad For Your Engine LIFE, Avoid Eviter Pour Prolonger LA Duree DE VIE DU Moteur Para Contribuir a LA Vida Útil DEL MOTOR, EviteStarting Engine OperationClose Fonctionnement Uso Adjusting Idling Speed HOW to USEStopping Engine Idle set screwReglage DU Regime DE Ralenti Ajuste DE LA Velocidad EN VacíoVis de reglage du ralenti Tornillo de fijación libre Comment UtiliserVertical cut Hedge Trimming TechniquesHorizontal cut Techniques DE Taillage DE Haies Técnicas DE RecorteMaintenance Maintenance ChartEntretien MantenimientoTableau D’ENTRETIEN Tabla DE MantenimientoReplacement Plug is Champion RCJ6Y or NGK BPMR7A AIR FilterFuel Filter Spark PlugEntretien Mantenimiento Intake AIR Cooling Vent Spark Arrester MA4Blades PARE-ETINCELLES MA4 Ouïe DE Refroidissement PAR AIRParachispas MA4 Ventilación DE Refrigeración DEL Aire DE AdmisiónSharpening MA7 Procedures to be Performed After Every 100 Hours of USEReduction Gearbox Procedures a Effectuer Toutes LES 100 Heures D’UTILISATION Affûtage MA7Reducteur Afilado MA7Storage DisposalEmission Control HT2200/CHT2200Mise au rebut Eliminación Rangement AlmacenamientoControl DE Emisiones 11. Guía de localización y solución de problemas Troubleshooting guideGuide de localisation des pannes HT2200 CHT2200 NotaParts list Key# Description Part Number Qty Engine Group HT2200 RCJ6Y Cutter Group CHT2200 Cutter Group CHT2200 Engine Group CHT2200 RCJ6Y Limited Warranty Garantie limitée Garantía Limitada Zenoah AMERICA, INC