Zenoah HT2200 manual SE6 SE7 SE8

Page 20

SE6

SE7

SE8

English

6. Set up

CHT2200

1.Attach the engine to the clutch housing of the cutter unit. Casually fix the front 2 points with the screws (.55" long).

2.After connecting the ground wire, install the rear handle to the clutch housing with the screw(2" long) and the nut.

3.Put the screw (1.6" long) through the ground wire terminal and the rear handle, and in to the engine mounting base. Securely tighten all of the engine mounting screws.

4.Attach the front handle onto the gear housing and fasten with 2 screws (1.2" long) and nuts.

5.Connect the throttle cable with the lever on the rear handle, and secure the end with the hardware attached to the handle.

6.Check the cable play and, if necessary, adjust between .04” and .08” by bending throttle wire receiver of the bracket with needle nose pliers.

20

Image 20
Contents HT2200 CHT2200 Contents Advertencias Contenidas EN EL Manual Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOITables des matieres Contenido Model HT2200 CHT2200 SpecificationsParts location Emplacement des pieces Situación de las piezas Fiche techniqueEspecificaciohes Modelo HT2200 CHT2200Symbols on the machine Emplacement PosiciónWorking Circumstance For safe operationWorking Condition Consignes de securite Instrucciones de seguridad Conditions DE TravailCondición DE Trabajo Circunstancias DE TrabajoWorking Plan Before Starting the EnginePlan DE Travail Plan DE TrabajoAvant DE Mettre LE Moteur EN Marche Antes DE Arrancar LA MáquinaCut only materials recommended by Using the ProductStarting the Engine Demarrage DU Moteur Utilisation DE LA MachineArranque DE LA Máquina Empleo DEL ProductoMaintenance If Someone ComesConsignes de securite Instrucciones de seguridad SI QUELQU’UN S’APPROCHEEntretien SI SE Acerca AlguienTransportation Handling FuelRefill after cooling the engine Manipulation DU Carburant TransportManejo DEL Combustible Llenar una vez que el motor se haya enfriadoSet up Blade Washer Keep LooseBolt Plate Nut Corrugate tube 2 Tie band Throttle cable 4 Throttle leverAssemblage Montaje SE6 SE7 SE8 Assemblage Montaje Recommended Mixing Ratio Gasoline 50OIL When using RedMax/ZENOAH genuine oilFuel Rapport DE Melange Recommande Essence 50 Huile Carburant CombustibleLors de l’utilisation de la véritable huile RedMax/ZENOAH Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteHOW to MIX Fuel Fueling the UnitAbastecimiento DE LA Unidad Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir For Your Engine LIFE, Avoid Eviter Pour Prolonger LA Duree DE VIE DU Moteur Para Contribuir a LA Vida Útil DEL MOTOR, EviteClose OperationStarting Engine Fonctionnement Uso Adjusting Idling Speed HOW to USEStopping Engine Idle set screwReglage DU Regime DE Ralenti Ajuste DE LA Velocidad EN VacíoVis de reglage du ralenti Tornillo de fijación libre Comment UtiliserHorizontal cut Hedge Trimming TechniquesVertical cut Techniques DE Taillage DE Haies Técnicas DE RecorteMaintenance Maintenance ChartEntretien MantenimientoTableau D’ENTRETIEN Tabla DE MantenimientoReplacement Plug is Champion RCJ6Y or NGK BPMR7A AIR FilterFuel Filter Spark PlugEntretien Mantenimiento Blades Spark Arrester MA4Intake AIR Cooling Vent PARE-ETINCELLES MA4 Ouïe DE Refroidissement PAR AIRParachispas MA4 Ventilación DE Refrigeración DEL Aire DE AdmisiónReduction Gearbox Procedures to be Performed After Every 100 Hours of USESharpening MA7 Procedures a Effectuer Toutes LES 100 Heures D’UTILISATION Affûtage MA7Reducteur Afilado MA7Storage DisposalEmission Control HT2200/CHT2200Control DE Emisiones Rangement AlmacenamientoMise au rebut Eliminación Guide de localisation des pannes Troubleshooting guide11. Guía de localización y solución de problemas HT2200 CHT2200 NotaParts list Key# Description Part Number Qty Engine Group HT2200 RCJ6Y Cutter Group CHT2200 Cutter Group CHT2200 Engine Group CHT2200 RCJ6Y Limited Warranty Garantie limitée Garantía Limitada Zenoah AMERICA, INC