Powermate P-RTT-196MD Emisson Control System Warranty, Your Warranty Rightes and Obligations

Page 23

Warranty (Continued)

• Save all instructions

B Emisson Control System Warranty

This MAT Engine Technologies, LLC (METL) outdoor power equipment engine complies with the emissions regulations of:

Powermate® Model No.

Regulatory Agency

 

 

P-RTT-196MD-[E]

United States Environmental Protection Agency (“U.S. EPA”)

P-RTT-196MD

United States Environmental Protection Agency (“U.S. EPA”) and State of California

To the extent there is any conflict between this Emissions Control System Warranty and the equipment manufacturer’s warranty, this Emissions Control System Warranty shall apply except where the equipment manufacturer’s warranty may provide a longer warranty period. Please read your warranty rights and obligations carefully. Some sections of the warranty may not apply to the specific equipment model you purchased. Unless specifically noted otherwise, the terms of the Emission Control System Warranty shall apply to all product engines covered within this manual.

Your Warranty Rightes and Obligations:

The California Air Resources Board, U.S. EPA and MAT Engine Technologies, LLC (METL) are pleased to explain the Emission Control Sys- tem Warranty on your new outdoor power equipment engine.

California (applies only to Model No. P-RTT-196MD-[E] and P-RTT-196MD

In California, new spark-ignited small off-road equipment engines must be designed, built and equipped to meet the State’s stringent anti-smog standards.

Other States, U.S. Territories

In other areas of the United States, your engine must be designed, built and equipped to meet the U.S. EPA emission standards for spark- ignited engines at or below 19 kilowatts.

All of the United States

MAT Engine Technologies, LLC (METL) must warrant the emissions control system on your power equipment engine for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your power equipment engine. Where a warrantable condition exists, METL will repair your power equipment engine at no cost to you including diagnosis, parts and labor.

Manufacturer’s Warranty Coverage:

The emissions control system is warranted for two years. If any emissions-related part on your engine is defective, the part will be repaired or replaced by METL.

Owner’s Warranty Responsibility

As the power equipment engine owner, you are responsible for the performance of the required maintenance listed in your owner’s manual. METL recommends that you retain all receipts covering maintenance on your power equipment engine, but METL can not deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

As the power equipment engine owner, you should however be aware that METL may deny your warranty coverage if your power equip- ment engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications.

You are responsible for presenting your power equipment engine to a distribution center or service center authorized by METL as soon as the problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact

MAT Engine Technologies, Inc.

6700 Wildlife Way

Long Grove, IL 60047

Tel: 1-800-737-2112

Questions? Call Toll Free at 1-800-737-2112

22

Copyright © 2009 MAT Engine Technologies, LLC

Image 23
Contents Operator’s Manual Rear Tine Rotary TillerControl and Operating Symbols Safety DefinitionsSafety Alert Symbols Safety Warning SymbolsResponsibility of Operator Important Safety InformationPreparation Safety Operation SafetyFuel Safety Operation SafetyChildren Safety Storage SafetyREPAIR, MAINTENANCE, and Adjustment Safety Parts & Features Product SpecificationsSafety Decals Assembly Install the Depth Regulator See Figure Install the Wheels See FigureInstall the Tines Install the Tine ShieldAttach Front Handle See Figure Attach Lower Handle See FigureAttach Upper Handle See Figure Engine Oil Engine PreparationStart-Up OperationCold Starts Restarting a Warm EngineTilling Idle SpeedOperating Speed Shutting DownCure the Levers in Drive Position Forward Lever See FigureDepth Regulator Lever See Figure AdjustmentsTilling Tips Belt Tension Adjustment See FigureTo increase belt tension To Decrease Belt TensionPeriodic Maintenance Schedule Table MaintenanceTab Change FORWARD/REVERSE BeltsCheck Tiller Transmission OIL Engine MaintenanceClean Tine Axle Shaft Check or Fill Engine CrankcaseHow to Prepare for Storage Technical ServiceProblem Possible Causes Solutions Powermate Rotary Tiller Limited Warranty WarrantyManufacturer’s Warranty Coverage Emisson Control System WarrantyYour Warranty Rightes and Obligations Limitations of Liability Warranty CoverageHow to Obtain Warranty Service ExclusionsWarranty Page Guárdese Este Manual Para Referencia Futura Símbolos de control y operación Definiciones de seguridadSímbolos de alerta sobre seguridad Símbolos de advertencia sobre seguridadSeguridad Durante LA Operación Información importante sobre seguridadResponsabilidad DEL Operador Seguridad Durante LA PreparaciónSeguridad DEL Combustible Información importante sobre seguridad ContinuaciónSeguridad Durante LA Operación Continuación Seguridad DE Niños Seguridad DE AlmacenamientoSeguridad Durante LA REPARACIÓN, Mantenimiento Y Ajuste Piezas y características Especificaciones del productoMarbetes de seguridad Montaje Marbetes de seguridad ContinuaciónCómo sacar la motocultivadora de la caja Instalar LAS Ruedas véase la figuraInstalar LAS Azadas Instalar LA Cubierta DE AzadasInstalar EL Asidero Frontal véase la figura Instalar EL Asidero Inferior véase la figuraCómo Revisar EL Nivel DE Aceite Y Llenar AL Nivel Apropiado Preparación del motorArranque OperaciónArranques EN Frío Rearranque DE UN Motor EN CalienteLabranza Régimen de marcha en vacíoVelocidad de operación ApagadoPalancas de control motriz seguro Palanca DE Retroceso véase la figuraAjustes Palanca DEL Regulador DE ProfundidadPara Reducir LA Tensión DE LA Correa Ajuste DE LA Tensión DE LA CorreaPara aumentar la tensión de la correa Programa de mantenimiento MantenimientoTabla DE Programa DE Mantenimiento Periódico Mantenimiento menor de la motocultivadora Mantenimiento ContinuaciónLimpiar LA Flecha DEL EJE DE Azadas Mantenimiento del motorRevisar LA Presión DE LAS Llantas LubricaciónCómo preparar la motocultivadora para almacenamiento Servicio técnicoProblema CAUSA/S POSIBLE/S Solución / Soluciones Diagnóstico y resolución de problemasGarantía Cobertura de la garantía del fabricante Garantía del sistema pro control de emisiones contaminantesDerechos y obligaciones al amparo de la garantía Limitaciones de responsabilidad Cobertura de la garantíaCómo obtener servicio de garantía ExclusionesGarantía Continuación