Troy-Bilt 643D-Tuffy/Bronco, 643B, 645A - Super Bronco manual Decals, Operating Symbols

Page 5

Decals

For your safety and the safety of others, vari- ous safety and operational decals are located on your unit (see Figure 1-2).

Keep the decals clean and legible at all times. Contact your local service dealer or the factory for replacements if any decals are damaged or missing.

Refer to the Parts List pages in this Manual for decal locations, descriptions and part num- bers.

Forward Clutch Bail

Starting Stabilization

Message (on engine)

Reverse Clutch Control

Operating Instruction

(Models 643B & 645A)

Warning Messages

Hot Surfaces Warning

Figure 1-2: Location of safety and operating decals.

Operating Symbols

 

 

 

R

 

Varioussymbols(shownhere,withworddescriptions)

 

 

 

maybeusedonthetillerandengine.

 

CHOKE

CHOKE

REVERSE

 

NOTE:Yourunitmaynothaveallofthesymbols.

ON

OFF

ROTATING TINES

 

 

 

 

 

 

BAIL

BAIL

 

 

 

 

 

ENGAGED

DISENGAGED

FAST

SLOW

STOP

TILLER DIRECTION

LEVER DIRECTION

 

WARNING

TO AVOID SERIOUS INJURY:

READ THE OWNER’S MANUAL.

KNOW LOCATIONS AND FUNCTIONS OF ALL CONTROLS.

KEEP ALL SAFETY DEVICES AND SHIELDS IN PLACE AND WORKING.

NEVER ALLOW CHILDREN OR UNINSTRUCTED ADULTS TO OPERATE TILLER.

SHUT OFF ENGINE AND DISCONNECT SPARK PLUG WIRE BEFORE MANUALLY UN- CLOGGING TINES OR MAKING REPAIRS.

KEEP BYSTANDERS AWAY FROM MACHINE.

KEEP AWAY FROM ROTATING PARTS.

USE EXTREME CAUTION WHEN REVERSING OR PULLING THE MACHINE TOWARDS YOU.

5

Image 5
Contents 11/11/05 Form no -00585E.fmCustomer Support Table of ContentsFinding Model Number Do not put hands or feet near or under rotating parts Safety Alert SymbolKeep children and pets away Refer to the Maintenance sectionsStarting the engine or engaging Use slower engine speedsDecals Operating SymbolsAssembly Steps AssemblyIntroduction Inspect UnitUse the handlebar to roll the tiller to a flat area Install Forward Clutch CableWith the Forward Clutch Bail Y, Fig While preventing the cable adjuster from turningCheck all nuts and screws for tightness Check Transmission OIL LevelIntroduction Wheel Drive PinsEngine Controls Ature package to identify the controls on your engineDepth Regulator Lever Handlebar Height AdjustmentIntroduction BREAK-IN Operation Following steps describe how to start and stop the engineStarting and Stopping Change engine oilOperating the Tiller For forward motion of the wheels and power to the tinesStopping the Engine and Tiller To move the Model 643C in reverse for short distancesTilling Tips & Techniques Tilling On Slopes Tilling Tips & Techniques CON’TClearing the Tines Read the following recommendations before tilling on slopesTerrace Gardening Loading and Unloading the TillerTiller Lubrication Transmission Gear OIL ServiceCheck Hardware Check Tire PressureRemoving⁄Installing a Tine Assembly Removing⁄Installing a Single TineBolo Tines Tine InspectionReplacement Belt Information Checking and AdjustingForward To Check Forward Belt TensionEngine Cleaning AIR Cleaner Service Engine OIL Service Forward Clutch Bail AdjustmentModels 643B & 645A only To Check Reverse Belt TensionSpark Arrester Screen Service Spark Plug ServiceOFF-SEASON Storage To Change the Engine OilProblem Possible Cause Correction TroubleshootingPage Models 643C, 643B & 645A Models 643C, 643B & 645A GW-1224-3 Front Model 643C Models 643C, 643B & 645A Page Page TROY-BILT Tiller Lifetime Limited Warranty Formulario N 769-00585ESp.fm Manual del OperadorBúsqueda DEL Número DE Modelo ÍndiceAsistencia AL Cliente Índice PáginaLea atentamente este Símbolo de alerta de seguridadLlene el tanque de combustible en exteriores con extremo Un embudo o pico para evitar derramesLa misma en cada pasada Mantenga a los niños y las mascotas alejadosAdvertencia Ctdad. Descripción IntroducciónInspeccione LA Unidad Directa Paso 4 Instale EL CableDEL Embrague DE Marcha Únicamente Modelos 643B Y 645A Controle el ajuste de todas las tuercas y los pernos Paso 6 Verificación del nivel del Aceite DE TransmisiónLa cultivadora se envía sin aceite en el motor Controles DEL Motor IntroducciónPasador de transmisión de las ruedas Identificar los controles del motorAjuste DE LA Altura DE LA Barra DE Control Arranque Y Detención Funcionamiento InicialCambie el aceite del motor Coloque las ruedas en la posiciónDetención del motor y la cultivadora Funcionamiento DE LA CultivadoraPara mover el modelo 643C marcha atrás en distancias cortas Los dientes se separen del sueloProfundidades Advertencia Ant Sugerencias Y Técnicas Para LA LabranzaEvite dejar huellas Preparación de losLabranza en Sugerencias Y Técnicas DE Labranza ContinuaciónLimpieza de los Labranza cuesta arriba y cuesta abajo labranza verticalJardinería en terrazas continuación Carga Y Descarga DE LA CultivadoraVerifique LA Presión DE Aire Lubricación DE LA CultivadoraModelos con neumáticos Graves o daños materialesPara drenar el aceite de engranajes de la transmisión Dientes BoloInspección de los dientes Retiro⁄Instalación de un solo dienteMarcha Directa Verificación Y AjusteAvance Marcha directaMantenimiento DEL Filtro DE Aire Limpieza DEL MotorMantenimiento DEL Aceite DE Motor 643B y 645AAjustes DE Control Mantenimiento DEL Filtro AntichispasAjuste DE LA Palanca DEL Estrangulador Para cambiar el aceite de motorProblema Causa Posible Corrección Solución DE ProblemasNotas Modelos 643C, 643B y 645A Modelos 643C, 643B Y 645A 16-18 x 3/4 No. de PiezaFrente Model 643C Modelos 643C, 643B Y 645A Notas Notas QUÉ Producto