Craftsman 919.670070 Clean and Replace Spark Plug, Replace Fuel In-Line Filter, Air Cleaner

Page 19

•Add fresh oil. See Add Engine Oil in the Opera- tion section of this manual.

•Start and run engine at idle to check for leaks.

•Stop engine. Re-check oil level, add oil if re- quired.

Air Cleaner

Do not use pressurized air or solvents to clean cartridge. Pressurized air can damage cartridge; solvents will dissolve cartridge.

To service air cleaner follow these steps:

•Unhook clips on both sides of cover and remove cover.

Clips

Cover

Body

Knob

Plate

Cartridge

Pre-cleaner

Body

•Remove knob and plate. Carefully remove air cleaner assembly to prevent debris from entering carburetor.

•To clean pre-cleaner and cartridge:

Pre-cleaner

•Separate from cartridge and wash in liquid detergent and water.

•Squeeze dry in a clean cloth.

•Saturate in engine oil. Squeeze in clean, absorbent cloth to remove all EXCESS oil.

Cartridge

•Gently tap on a flat surface.

•Reassemble clean (or new ) pre-cleaner on clean (or new) cartridge.

•Reinstall air cleaner assembly, plate and knob in body.

•Replace cover and reattach clips to body.

Clean Cooling System

Debris may clog the engine's air cooling system. Remove blower housing and clean area shown to prevent overheating and engine damage.

Clean

Clean and Replace Spark Plug

Check spark plug yearly or every 100 operating hours.

•Clean area around spark plug.

•Remove and inspect spark plug.

•Replace spark plug if electrodes are pitted, burned or porcelain is cracked.

•Check electrode gap with wire feeler gauge and set gap .030 if necessary.

•Install spark, tighten securely.

.030" (0.76mm)

Wire Gauge

Spark Plug

Replace Fuel In-Line Filter

•Disconnect spark plug wires and keep away from spark plugs.

Drain fuel tank or close fuel shut-off valve before replacing fuel filter.

•Replace in-line fuel filter.

In-line Fuel Filter

19 — ENG

MGP-670070

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Generator Owners ManualSold by Sears Canada, Inc., Toronto, Ont. M5B2B8 Table of Contents Risk of Electrocution and Fire Safety Guidelines DefinitionsImportant Safety Instructions Hazard What could Happen HOW to Prevent ITRisk of Electrocution and Fire cont’d Fined Area Risk of FireOr wall. do not Operate Unit Indoors or in ANY CONRead and Understand ALL Warnings Before Risk of Breathing Inhalation HazardOn your generator Protector will void the warrantyRisk of Unsafe Operation L. listed voltage surgeRisk of Moving Parts Risk of HOT SurfacesRisk from Lifting Carton Contents AssemblyRemove Generator from Carton Tools Needed for AssemblyNut Solenoid Installation of BatteryNegative Battery Cable Connection Star Washer Grounding the GeneratorInstalling Wheel KIT Know Your Generator OperationNot shown Obtaining Electricity from Generator ReceptaclesLOW OIL Shutdown Generator CapacityGasoline Connecting Generator To Main Electrical SupplyBefore Starting Engine Adding Engine OilStopping Engine To Start Your GeneratorFor recoil start Customer Responsibilities Table MaintenanceConnecting Electrical Loads Maintenance TaskEngine Maintenance Generator MaintenanceGeneral Recommendations Replace Fuel In-Line Filter Clean and Replace Spark PlugAir Cleaner Clean Cooling SystemGovernor Service AdjustmentsStorage CarburetorProblem Cause Correction Troubleshooting GuideEmissions Control Systems Statement Owner’s Warranty ResponsibilitiesENG ENG ENG Service and Repair Parts Vendu par Sears Canada, Inc., Toronto, Ont. M5B 2B8 Génératrice DEResponsabilités DU Client Entente D’ENTRETIENConserver CES Directives Risques Délectrocution ET D’INCENDIERisques Prévention Rieur OU Dans UN Endroit Clos Risques D’INCENDIERisques AUX Voies Respiratoires ET Risques D’INHALATION Les moteurs à essence produisent Génératrice Risques D’UNE Utilisation DangereuseRisques Reliés AUX Pièces Mobiles Risques Reliés AUX Surfaces ChaudesRisques Lors DU Levage Sac à pièces pour la pose de la batterie Contenu DE L’EMBALLAGESac à pièces Pièces et boîte à pièces pour l’ensemble de rouesRetrait DE LA Génératrice DE SON Emballage Outils Requis Pour L’ASSEMBLAGEMise À LA Terre DE LA Génératrice Pose Typique D’UNE BatterieÉcrou Solénoï de Support du Moteur Pose DE L’ENSEMBLE DE RouesBien Connaître Votre Génératrice FonctionnementComment Obtenir DE L’ÉLECTRICITÉ DE LA Génératrice PrisesDispositif D’ARRÊT Suite À UN Niveau BAS D’HUILE Capacité DE LA GénératriceEssence Remplissage d’huile moteur Avant DE Démarrer LE MoteurDémarrage à rappel Démarrage du moteurArrêt du moteur Démarrage électriqueTâche D’ENTRETIEN EntretienTableau DES Responsabilités DU Client Branchement DE Charges ÉlectriquesHuile Recommandations GénéralesEntretien DE LA Génératrice Entretien DU MoteurNettoyage du système de refroidissement Nettoyage et remplacement de la bougie dallumageRemplacement du filtre à carburant en ligne Filtre à airEntreposage Réglages D’ENTRETIENDirectives Pour L’ENTREPOSAGE Problème Cause Correction Guide DE DépannageResponsabilités de garantie du propriétaire Remarque Remarque Remarque Entretien ET Pieces DE Rechange

MGP-670070, 919.670070 specifications

The Craftsman 919.670070, also known as MGP-670070, is a premier solution for those seeking a reliable and efficient air compressor. This model stands out in the crowded market of air compressors due to its robust design and versatile functionality, making it a go-to choice for both professionals and DIY enthusiasts.

One of the primary features of the Craftsman 919.670070 is its powerful motor. With a horsepower rating that ensures high performance, it delivers a consistent airflow suitable for a variety of tasks, from inflating tires to powering pneumatic tools. This capability makes it an ideal asset for both home workshops and professional garage settings.

The tank capacity of the MGP-670070 is another highlight. With a sizeable tank, it can store ample compressed air, allowing users to complete larger tasks without the need for frequent refills. This characteristic greatly enhances productivity, as users can work without interruption.

Portability is a significant consideration for many users, and the Craftsman 919.670070 excels in this aspect. Its compact design, combined with sturdy wheels and a comfortable handle, ensures that it can be easily transported from one location to another, making it perfect for job sites or moving around the home.

Safety features have not been overlooked in the design of the MGP-670070. It comes equipped with an automatic shut-off mechanism that activates when the desired pressure is reached, preventing over-pressurization and extending the lifespan of the machine. Additionally, it often includes a thermal overload protection system that helps protect the motor from overheating.

The compressor's user-friendly control panel features gauges that provide clear readings of both tank pressure and outlet pressure, ensuring that users can monitor performance easily. Coupled with quick-connect fittings, the MGP-670070 allows for fast and uncomplicated hose connections, streamlining the workflow.

Technologically, this model includes a noise-reduction design that operates at lower decibel levels compared to traditional compressors. This feature makes it particularly appealing for use in residential areas where noise can be a concern.

In summary, the Craftsman 919.670070, MGP-670070, is not just another air compressor on the market; it embodies a combination of power, efficiency, and user-centric design. Whether you are a seasoned professional or a weekend warrior, this compressor meets various needs with reliability and ease of use, making it a valuable addition to any toolkit.
Top Page Image Contents