Briggs & Stratton 030235-01 Assembly, Equipment Description, Unpack Generator, Shipment Contents

Page 6

Equipment Description

Read this manual carefully and become familiar with your generator. Know its applications, its limitations and any hazards involved.

The generator is an engine–driven, revolving field, alternating current (AC) generator. It was designed to supply electrical power for operating compatible electrical lighting, appliances, tools and motor loads. The generator’s revolving field is driven at about 3,600 rpm by a single- cylinder engine.

CAUTION

Exceeding generators wattage/amperage capacity can damage generator and/or electrical devices connected to it.

•DO NOT exceed the generator’s wattage/amperage capacity. See Don’t Overload Generator in the Operation section.

Every effort has been made to ensure that the information in this manual is both accurate and current. However, the manufacturer reserves the right to change, alter or otherwise improve the generator and this documentation at any time without prior notice.

The Emission Control System for this generator is warranted for standards set by the Environmental Protection Agency and the California Air Resources Board.

Assembly

Your generator requires some assembly and is ready for use after it has been properly serviced with the recommended fuel and oil level is verified.

If you have any problems with the assembly of your generator, please call the generator helpline at

1-800-743-4115. If calling for assistance, please have the model, revision, and serial number from the data tag available. See Generator Controls and Features for data tag location.

Unpack Generator

1.Set the carton on a rigid, flat surface.

2.Remove everything from carton except generator.

3.Open carton completely by cutting each corner from top to bottom.

4.Leave generator on carton to install wheel kit.

Shipment Contents

The generator is supplied with:

•Operator’s manual

•Adapter cord set

•Wheel kit

Install Wheel Kit

NOTE: Wheel kit is not intended for over-the-road use.

You will need the following tools to install these components:

•13 mm wrench

•Socket wrench with a 13 mm socket

•Pliers

•Safety glasses

Refer to Figure 1 and install the wheel kit as follows:

1a

B

A

C

F A

E

B D

G

Figure 1 — Install Wheel Kit

A - Axle

B - Wheel

C - Flat Washer

D - E-Ring

E - Support Leg

F - M8 x 16 mm Capscrews

G - Hex Nuts

1.Tip generator so that engine end is up.

2.Slide axle (A) through both mounting brackets.

3.Place a wheel (B) on each side as shown in Figure 1a.

4.Place a washer (C) on axle and then place an e-ring (D) in axle groove.

CAUTION

E-rings can cause eye injury.

E-rings can spring back and become airborne when installing or removing.

•Always wear eye protection when installing/removing e-rings.

4www.briggsandstratton.com

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Watts Where to Find Us Revision Serial Number Engine Model Number Date PurchasedTable of Contents Safety Rules Hazard Symbols and MeaningsWhen operating equipment When adding or draining fuelWhen starting equipment When transporting or repairing equipmentInstall Wheel Kit AssemblyShipment Contents Equipment DescriptionAdd Fuel When adding fuelVerify Engine Oil Level Type of FuelGenerator Location Connecting to a Building’s Electrical SystemSystem Ground Special RequirementsFeatures and Controls 120/240 Volt AC, 30 Amp Locking Receptacle120/240 Volt AC, 30 Amp, Locking Receptacle ReceptaclesGenerator Adapter Cord Set Volt AC, 20 Amp, Duplex ReceptaclesOperation Starting the EngineConnecting Electrical Loads Stopping the EngineCapacity Power ManagementDon’t Overload Generator ExampleGeneral Recommendations MaintenanceMaintenance Schedule Emissions ControlOil Generator MaintenanceCleaning Oil RecommendationsChecking Oil Level Adding Engine OilChanging Engine Oil Service Air Cleaner Service Spark PlugClean Spark Arrester Screen Engine Air Cooling System Carburetor AdjustmentClean and inspect the spark arrester as follows Check Valve ClearanceStorage Troubleshooting Maintenance Items SpecificationsReplacement Parts Engine Technical InformationOwner’s Warranty Responsibilities Warranted PartsLength of Coverage Maintenance Consequential Coverage No ChargeClaims and Coverage Exclusions Warranty Period This page reserved Dónde encontrarnos Controles y características Resolución de problemas Especificaciones GarantíasMontaje OperandoNormas de seguridad Símbolos de peligro y sus significadosCuando opere el equipo Cuando anada combustible o vacíe el depósitoCuando ponga en funcionamiento el equipo Cuando transporte o repare el equipoDesembalaje del generador MontajeDescripción del equipo Contenido de la cajaCuando anada combustible Comprobar el nivel de aceite del motorAgregue combustible Tipo de gasolinaUbicación del generador Tierra del sistemaConexión al sistema eléctrico de un edificio Requisitos EspecialesControles y características del generador Dispositivo de seguridad de 120/240 V, 30 a Tomas eléctricasTomas eléctricas dobles de 120 V CA y 20 a Juego de cables del adaptador del generadorOperando Encienda el motorConexión de cargas eléctricas Parada del motorEjemplo No sobrecargar el generadorCapacidad Control de la energíaRecomendaciones Generales MantenimientoPlan de mantenimiento Control de emisionesAceite Mantenimiento del GeneradorLimpieza Recomendaciones sobre el aceiteComprobación del Nivel de Aceite Adición de Aceite del MotorCambio de Aceite del Motor Servicio del depurador de aire Servicio del bujíaLimpie la Pantalla Apagachispas Ajuste del Carburador Sistema de refrigeración de aireComprobación de holgura de la válvula Limpie e inspeccione el apagachispas de la siguiente maneraAlmacenamiento Resolución de problemas Problemo Causa AccionInformación técnica sobre el motor Responsabilidades de la garantía del propietario Piezas garantizadasDuración de la cobertura Mantenimiento Servicio gratuitoSolicitudes y exclusiones de cobertura Cobertura de daños derivadosPeríodo DE Garantía

030235-01 specifications

The Briggs & Stratton 030235-01 is a key component in the realm of outdoor power equipment, renowned for its reliability and performance. This model is primarily designed for use in portable generators, offering a powerful and efficient engine that meets the demands of users looking for dependable energy solutions.

One of the standout features of the 030235-01 is its impressive engine output. With a robust design, it provides a reliable source of power for various applications, whether for home backup during outages or for job sites requiring portable energy. This model is built with a reliable four-stroke engine, allowing for smooth operation and reduced emissions compared to two-stroke engines. This makes it an environmentally friendly option for those needing outdoor power.

The motor is equipped with advanced technologies that enhance its performance. The overhead valve (OHV) design optimizes engine efficiency while maintaining low operating temperatures, ensuring longer life and reduced wear. Additionally, the engine features a splash lubrication system, taking care of critical components to minimize friction and ensure a smooth operation even under heavy loads.

Another key characteristic of the Briggs & Stratton 030235-01 is its easy-starting capability. Many users appreciate this feature, especially during emergencies when time is of the essence. The primer bulb and choke system facilitate a hassle-free startup, allowing users to get the engine running with minimal effort.

Durability is also a key focus of this engine's design. Constructed with high-quality materials and comprehensive engineering, the 030235-01 can withstand the rigors of frequent use. It has a sturdy build that resists corrosion, making it suitable for various outdoor conditions. Coupled with routine maintenance, this generator can serve users for years to come.

On the ease of use front, the Briggs & Stratton 030235-01 is designed for straightforward operation. It has an intuitive control panel that enables users to manage their power needs without any confusion, enhancing the overall user experience.

In summary, the Briggs & Stratton 030235-01 stands out for its powerful engine output, innovative technologies such as OHV design and splash lubrication, durability under various conditions, and user-friendly operation. This combination makes it a preferred choice for those seeking reliable portable power solutions.
Top Page Image Contents