Briggs & Stratton 206494GS Clean Cooling System, Check Valve Clearance, Carburetor Adjustment

Page 18

Clean Cooling System

Over time debris may accumulate in cylinder cooling fins and cannot be observed without partial engine disassembly. For this reason, we recommend you have a Briggs & Stratton authorized dealer clean the cooling system (A) per recommended intervals (see Maintenance Schedule in the Maintenance section). Equally important is to keep top of engine free from debris. Also see Cleaning.

A

Check Valve Clearance

Regular valve clearance check and adjustment will improve performance and extend engine life. This procedure cannot be done without partial engine disassembly and the use of special tools. For this reason we recommend that you have an authorized dealer check and adjust valve clearance at

250 hours or as recommended (see Maintenance Schedule in the Maintenance section).

Carburetor Adjustment

The carburetor on this engine is low emission. It is equipped with a non-adjustable idle mixture valve. Top speed has been set at the factory. If adjustment is required, see a Briggs & Stratton authorized dealer.

CAUTION

Excessively high operating speeds increase risk of injury and damage to generator.

Excessively low speeds impose a heavy load.

•DO NOT tamper with governed speed. Generator supplies correct rated frequency and voltage when running at governed speed.

•DO NOT modify generator in any way.

18	BRIGGSandSTRATTON.COM

Image 18

Contents Operator’s Manual Engine Where to Find UsGenerator Date PurchasedTable of Contents Safety alert symbol is used with a signal word Operator SafetySafety Rules Hazard Symbols and MeaningsEngine exhaust from this product contains Broken bones, fractures, bruises, or sprains could resultGenerator produces hazardous voltage When Adjusting or Making Repairs to Your GeneratorWhen Testing for Engine Spark Contact with muffler area can result in serious burnsInstall Wheel Kit AssemblyShipment Contents Unpack GeneratorFuel must meet these requirements Clean area around fuel fill cap, remove capAdd Fuel High AltitudeGenerator Location Connecting to a Building’s Electrical SystemSystem Ground Special RequirementsFeatures and Controls 120/240 Volt AC, 30 Amp, Locking Receptacle Cord Sets and ReceptaclesNema L14-30 Volt AC, 20 Amp, Duplex ReceptaclesOperation Starting the EngineConnecting Electrical Loads Stopping the EngineMove fuel valve to Off position Don’t Overload Generator Wattage Reference GuideMaintenance Maintenance ScheduleGenerator Maintenance Checking Oil Level Engine MaintenanceOil Recommendations Adding Engine OilService Spark Arrester Service Air CleanerService Spark Plug Clean and inspect the spark arrester as followsClean Cooling System Carburetor AdjustmentCheck Valve Clearance Storage Troubleshooting Emissions Control System Warranty Owner’s Warranty ResponsibilitiesWarranties Maintenance Emission InformationClaims and Coverage Exclusions Limited Warranty AC Load Current Product SpecificationsCommon Service Parts 800Manual del Operario Motor Dónde encontrarnosGenerador Fecha de compraMontaje Resolución de problemas GarantíasSeguridad de operario Controles y característicasReglas de seguridad Seguridad de operarioDescripción del equipo Símbolos de peligro y sus significadosPeligro Precaución Contenido de la caja MontajeDesembalaje del generador Instale el juego de ruedasAgregue combustible El combustible debe reunir los siguientes requisitosGran altitud Ubicación del generador Tierra del sistemaConexión al sistema eléctrico de un edificio Requisitos especialesControles y características Del motor y está equipado con una pantalla apagachispasJuegos de cordones y enchufes conectores Dispositivo de seguridad de 120/240 V, 30 aToma eléctricas dobles de 120 V CA y 20 a Operando Encienda el motorEl motor podría petardear, incendiarse o dañarse Conexión de cargas eléctricasParada del motor Gire la válvula de combustible blanca hasta la posición OffEjemplo No sobrecargar el generadorCapacidad Control de la energíaRecomendaciones generales MantenimientoPlan de mantenimiento Control de emisionesComprobación del nivel de aceite Mantenimiento del motorAceite Recomendaciones sobre el aceite Adición de aceite del motorServicio del depurador de aire Servicio del bujíaLimpie la pantalla apagachispas Comprobación de holgura de la válvula Limpie e inspeccione el apagachispas de la siguiente maneraSistema de refrigeración de aire Ajuste del carburadorAlmacenamiento Resolución de problemas Problemo Causa AccionResponsabilidades de la garantía del propietario GarantíasGarantía del sistema de control de emisiones Operaciones de mantenimiento que se enumeran en lasInformación sobre emisiones Garantía Limitada Especificaciones del producto Servicio común despideCorriente Carga de C.A