Craftsman C950-52930-0 Lubrication Every 25 Hours, Disc Drive Plate, Clean all excess grease

Page 22

NEED PARTS? VISIT HTTP://WWW.MANUALBUDDY.COM/PARTS

CUSTOMER RESPONSIBILITIES

LUBRICATION - EVERY 25 HOURS

Disc Drive Plate

Lubricate Disc Drive Plate every twenty-five (25) hours and at the end of the season and/or before storage.

To Lubricate:

3.Position speed selector lever in first (1) forward gear.

4.Stand the snow blower up on the auger housing end.

5.Remove the bottom panel.

6.Turn disc drive plate clockwise by hand until grease zerk is clearly visible at front center (see Figure 25).

7.Place a coin or (a shim of equal thickness) between the rubber friction wheel and disc drive plate to prevent rub- ber friction wheel contacting the drive disc (see Figure 25).

8.To grease zerk, use a hand grease gun, lubricate with a Hi Temp EP Moly grease. See inset of Figure 25. DO NOT over fill or allow grease to come in contact with the disc drive plate or fricfion wheel or damage will result. Fill zerk only until grease becomes visible below bearing as- sembly located under grease zerk.

Plate

Friction

Wheel
	Bearing	Point	at
	Assembly	Point	at
	Assembly	which
Disc		should		be
Drive		grease
Drive		visible
Plate	Shim placed in gap

9. Remove		coin used in step 11. Make sure that a gap exists			_._		Between Friction
between		the friction wheel and	the disc drive	plate.			Wheel and Disc Drive
between		the friction wheel and	the disc drive	plate.		_	Plate
NOTE:	Clean all excess grease		or oil found	on the			Grease Zerk
friction	disc	hub.

Figure 25

CAUTION: Do not allow grease or oil to contact the rubber friction wheel or the disc drive plate.

Hexshaft- wipe with 5W30 motor oil before

storage and at the begin- ning of each season

Chains-Lubricate chains with a chain type lube be- fore storage and at the

beginning of each sea- son.

WARNING: If the disc drive

plate or friction wheel

come in contact with

grease or oil damage to rubber friction wheel will

result.

If grease or oil come in con-

tact with the disc drive plate or friction wheel, make sure

to clean the plate and wheel

thoroughly with a alcohol base solvent,

Use a HI Ternp EP Moley

grease to lubricate grease zerk on disc drive plate every 25 hours.

Figure 26

F-001008J

22

NEED PARTS? VISIT HTTP://WWW.MANUALBUDDY.COM/PARTS/

Image 22

Contents Sears Canada INC., TORONTO, Ontario M5B 2B8 001008J 12/13/99PrintedinU.S.A Rules for Safe Operation PreparationMaintenance and Storage Owners Information Maintenance AgreementWheeled Snow Blower Table of Contents Contents of Shipping Carton AssemblyTools Required for Assembly Parts Bags ContentsUnpacking Snow Chute Assembly Upper Handleand Crank Assembly Connect Control Cable SpringsSpeed Select Lever Remote Chute Control Knob Engine and Snow Blower Operating Controls Engine operating controls and their functions are as followsSnow Blower Operation Wheel Lock OUT PIN Fill GAS Temperature Type of OILBefore Starting Engine OOFWarm Engine Start Recoil Starter Minutes before blowing snow in temperatures below 0OFTo Start Engine Cold Engine Start Recoil StarterRemove finger from primer vent hole between USE of Electric StarterCold Engine Start Electric Starter See no TAG and Figure PushesWarm Engine Start Electric Starter Start EngineOperating Tips Recoil StarterProcedure Service RecommendationsService Recommendations After Each USEAS Required Customer ResponsibilitiesSnow Blower Lubrication AT StorageDisc Drive Plate Clean all excess greaseLubrication Every 25 Hours DiscEngine SAE Viscosity GradesAuger Housing Height Adjustment To Adjust Scraper BAR ADJUSTMENT/REPAIRTo Adjust Skid Height Traction Drive Belt Belt AdjustmentAuger Drive Belt Belt Replacement Auger Drive Belt see FigureBelt Guide Adjustment Cable Adjustment Traction Drive and Auger DriveFriction Wheel Adjustment If an adjustment is required, proceed as followsFriction Wheel Replacement Auger Shear Bolt Replacement Spark Plug Adjustment see FigureOFF-SEASON Storage StorageFireARNINGorflame.Drain gasoline outdoors, away from Trouble Shooting Chart Problem Look For RemedyENGINE/ Moteur Key No. NOsur ie SchemaDescriptionDescription De piece Drive COMPONENTS/ Batide Montagedu Moteur Key No. NOsur le SchemaDescription Drive COMPONENTS/ B.&,TIDE Montagedu Moteur108 111 109 140 Schema Description De pieceFrame Componentsi Bati 103 145 NOsur ieGear Casei BOiTER 340482 Auger Housingi VIS Sans FIN524 525 DISCHARGECHUTE/ DI=FLECTEURDE Goulotte 603Wheelsi Roue 673Headlighti Montagedu Phare 621 622 632 627 623 NOsurieHandle ! Poignie Sur le Controlpaneli Panneaude Commande HexnylSchema Description Electric Starter / ElectriqueChute ROD / Goulotte Tige 855862 850992 994 995 Remotechute CONTROL/ Diflecteurde Goulotte996 971 Decals / Autocollants 827 826282 NOsurie SchemaDescription Palier27915A Rf .27272A GL20A 37 0 RingNOsurie Schema Description Key No. No surie SchemaDescription RingOOIOO8J Engine Model Decal Blower Model DecalSerial No Service and Repair Parts Swars Swars Sears INC., TORONTO, Ontario M5B 2B8Conseils DE Securite Entretien ET Remisage Responsabilitis DU Client Avis AU ClientContrat Dentretien Garantie Limitie DE 2 ANS Pour LE CHASSE-NEIGE CraftsmanTables DES Matii RES Carton Dexpedition MontageOutils Requis Pour LE Montage SAC DE Pieces ContenantDfballage Montage DE LA Goulotte Branchement DES Cables DE Commande Montage DE LA Poignee Superieure ET DE LA ManivelleSgLECTEUR DE Vitesse Poignfe DE Commande DU Dfversoir Distance Levier de commande du ddflecteur b distance- Pousser Commandes DU Moteur ET DU CHASSE-NEIGEVoir Figure Les commandes du moteur et leurs fonctions sont UtilisationRouge Utilisation DU CHASSE-NEIGERemarque BlancGoupille DE Blocage DE Roue Niveaux DE Viscositi SAE Avant LA Mise EN Marche DU MoteurAvant Larrit Remplir DessenceDemarreur .&.CORDE Mise EN Marche DU MoteurMise EN Marche DU Moteur Chaud Utilisation DU Dfmarreur Flectrique Don de la prise residentielle dabord 001008JMarreur Mise EN Marche DU Moteur Chaud DieRemarque Un moteur chaud peut tre mis en marche Conseils Dutilisation Ddmarreur & cordeProcfdure Calendrier DentretienCalendrier Dentretien Apres Chaque UtilisationLubrification Avant Remisage CHASSE-NEIGEComme Requis Lubrification -TOUTES LES 10 HeuresLubrification Toutes LES 25 Heures Plateau de commande du disqueResponsabilites DE Client Pour lubrifierRemarque Lhuile se vidange mieux Iorsquelle est chaude MoteurSauf Rfglage DES Patins REGLAGES/REPARATIONSPour rdgler les patins procdder comme suit Reglage DES Courroies Courroie DE Commande DES RouesCourroie DE LA VIS Sans FIN Remplacement DES Courroies Courroie DE LA VIS Sans FIN Voir FigureReglage DES Guide DE Courroie Voir Figure Rdglage ventuel voir FigureReglage DU Disque DE Friction Si un rdglage est ndcessaire, procdder comme suitRemplacement DU Disque DE Friction Remplacement DES Boulons DE Cisaillement DE LA VIS Sans FIN Remisage Remisage Hors SaisonTableau DE Diagnostic Problfme Cause RemfdeComment Obtenir DES PI#CES DE Rechange De srieEntretien ET Pieces DE Rechange Composez LE