Craftsman C950-52930-0 owner manual Belt Adjustment, Traction Drive Belt, Auger Drive Belt

Page 25

NEED PARTS? VISIT HTTP://WWW.MANUALBUDDY.COM/PARTS

ADJUSTMENT/REPAIR

BELT ADJUSTMENT

Traction Dnve Belt

Belts stretch during normal use. If you need to adjust the belts due to wear or stretch, proceed as follows.

Traction Drive Pulley

Belt

TRACTION DRIVE BELT

Traction drive belt has constant spring pressure and does not require adjustment.

Replace belt if it is slipping. (See "Belt Replacement" in this section of the manual).

Traction

Idler

Pulley

Auger

Idler

Pulley

AUGER DRIVE BELT

If your snow blower will not discharge snow, check the control cable adjustment. If it is correct, then check the condition of the auger drive belt. It may be damaged or loose. If it is damaged, replace it (see Belt Replacement in this section of the manual). If the auger drive belt is loose, adjust as follows.

1.Disconnect spark plug wire.

2.Remove belt cover.

3.Loosen nut on auger idler pulley and move auger idler pulley towards belt about 1/8 inch (3 mm) (see Figure 30).

4.Tighten nut.

5.Have someone engage auger drive clutch. Check ten- sion on belt (opposite idler pulley). Belt should deflect about 1/2 inch (12.5 mm) with moderate pressure (Figure 31). You may have to move idler pulley more than once to obtain the correct tension.

6.Reinstall belt cover.

7.Whenever belts are adjusted or replaced, the cables will need to be adjusted. (See "Cable Adjustment" in this sec- tion of the manual).

Figure 30

	l	'_"_r_-		Auger
		4-		E%ve
				Pulley
	_-	_	_	1/2 inch
idler.---_-4_V"		_j /	\_	Deflection
Pulley	I0,	_7	\_
Engaged	_	f	\_
	__*--			impeller
				Figure 31

8.Reconnect the spark plug wire.

F-001008J

25

NEED PARTS? VISIT HTTP://WWW.MANUALBUDDY.COM/PARTS/

Image 25

Contents Sears Canada INC., TORONTO, Ontario M5B 2B8 001008J 12/13/99PrintedinU.S.A Preparation Rules for Safe OperationMaintenance and Storage Owners Information Maintenance AgreementWheeled Snow Blower Table of Contents Tools Required for Assembly AssemblyContents of Shipping Carton Parts Bags ContentsUnpacking Snow Chute Assembly Connect Control Cable Springs Upper Handleand Crank AssemblySpeed Select Lever Remote Chute Control Knob Engine operating controls and their functions are as follows Engine and Snow Blower Operating ControlsSnow Blower Operation Wheel Lock OUT PIN Before Starting Engine Temperature Type of OILFill GAS OOFTo Start Engine Minutes before blowing snow in temperatures below 0OFWarm Engine Start Recoil Starter Cold Engine Start Recoil StarterCold Engine Start Electric Starter See no TAG and Figure USE of Electric StarterRemove finger from primer vent hole between PushesStart Engine Warm Engine Start Electric StarterRecoil Starter Operating TipsService Recommendations Service RecommendationsProcedure After Each USESnow Blower Customer ResponsibilitiesAS Required Lubrication AT StorageLubrication Every 25 Hours Clean all excess greaseDisc Drive Plate DiscSAE Viscosity Grades EngineAuger Housing Height Adjustment To Adjust Scraper BAR ADJUSTMENT/REPAIRTo Adjust Skid Height Traction Drive Belt Belt AdjustmentAuger Drive Belt Auger Drive Belt see Figure Belt ReplacementCable Adjustment Traction Drive and Auger Drive Belt Guide AdjustmentIf an adjustment is required, proceed as follows Friction Wheel AdjustmentFriction Wheel Replacement Spark Plug Adjustment see Figure Auger Shear Bolt ReplacementOFF-SEASON Storage StorageFireARNINGorflame.Drain gasoline outdoors, away from Problem Look For Remedy Trouble Shooting ChartENGINE/ Moteur Key No. NOsur ie SchemaDescriptionDescription De piece Drive COMPONENTS/ Batide Montagedu Moteur Drive COMPONENTS/ B.&,TIDE Montagedu Moteur Key No. NOsur le SchemaDescriptionFrame Componentsi Bati Schema Description De piece108 111 109 140 103 145 NOsur ie340 Gear Casei BOiTER482 Auger Housingi VIS Sans FIN524 525 603 DISCHARGECHUTE/ DI=FLECTEURDE Goulotte673 Wheelsi Roue621 622 632 627 623 NOsurie Headlighti Montagedu PhareHandle ! Poignie Sur le Hexnyl Controlpaneli Panneaude CommandeElectric Starter / Electrique Schema Description855862 850 Chute ROD / Goulotte Tige992 994 995 Remotechute CONTROL/ Diflecteurde Goulotte996 971 827 826 Decals / Autocollants282 Palier NOsurie SchemaDescription27915A Rf .27272A 37 0 Ring GL20ANOsurie Schema Description Ring Key No. No surie SchemaDescriptionOOIOO8J Engine Model Decal Blower Model DecalSerial No Service and Repair Parts Sears INC., TORONTO, Ontario M5B 2B8 Swars SwarsConseils DE Securite Entretien ET Remisage Contrat Dentretien Avis AU ClientResponsabilitis DU Client Garantie Limitie DE 2 ANS Pour LE CHASSE-NEIGE CraftsmanTables DES Matii RES Outils Requis Pour LE Montage MontageCarton Dexpedition SAC DE Pieces ContenantDfballage Montage DE LA Goulotte Montage DE LA Poignee Superieure ET DE LA Manivelle Branchement DES Cables DE CommandeSgLECTEUR DE Vitesse Poignfe DE Commande DU Dfversoir Distance Voir Figure Les commandes du moteur et leurs fonctions sont Commandes DU Moteur ET DU CHASSE-NEIGELevier de commande du ddflecteur b distance- Pousser UtilisationRemarque Utilisation DU CHASSE-NEIGERouge BlancGoupille DE Blocage DE Roue Avant Larrit Avant LA Mise EN Marche DU MoteurNiveaux DE Viscositi SAE Remplir DessenceDemarreur .&.CORDE Mise EN Marche DU MoteurMise EN Marche DU Moteur Chaud Don de la prise residentielle dabord 001008J Utilisation DU Dfmarreur FlectriqueMarreur Mise EN Marche DU Moteur Chaud DieRemarque Un moteur chaud peut tre mis en marche Ddmarreur & corde Conseils DutilisationCalendrier Dentretien Calendrier DentretienProcfdure Apres Chaque UtilisationComme Requis CHASSE-NEIGELubrification Avant Remisage Lubrification -TOUTES LES 10 HeuresResponsabilites DE Client Plateau de commande du disqueLubrification Toutes LES 25 Heures Pour lubrifierRemarque Lhuile se vidange mieux Iorsquelle est chaude MoteurSauf Rfglage DES Patins REGLAGES/REPARATIONSPour rdgler les patins procdder comme suit Reglage DES Courroies Courroie DE Commande DES RouesCourroie DE LA VIS Sans FIN Voir Figure Remplacement DES Courroies Courroie DE LA VIS Sans FINRdglage ventuel voir Figure Reglage DES Guide DE Courroie Voir FigureSi un rdglage est ndcessaire, procdder comme suit Reglage DU Disque DE FrictionRemplacement DU Disque DE Friction Remplacement DES Boulons DE Cisaillement DE LA VIS Sans FIN Remisage Hors Saison RemisageProblfme Cause Remfde Tableau DE DiagnosticDe srie Comment Obtenir DES PI#CES DE RechangeComposez LE Entretien ET Pieces DE Rechange