Craftsman C950-52930-0 owner manual Belt Replacement, Auger Drive Belt see Figure

Page 26

NEED PARTS? VISIT HTTP://WWW.MANUALBUDDY.COM/PARTS

 

ADJUSTMENT/REPAIR

BELT REPLACEMENT

14. Replace top two bolts. Retighten bottom two bolts. See

 

Figure 32.

AUGER DRIVE BELT (SEE FIGURE 30)

1.Drain the gasoline from the fuel tank by removing the fuel line. Drain the gas and reinstall the fuel line.

,_ fromWARNING:fireor Drainflame. the gasoline outdoors, away

15.Reinstall belt cover.

16.Reconnect spark plug wire.

TRACTION DRIVE BELT

Traction drive belt has constant spring pressure and does not require adjustment.

2.Disconnect spark plug wire.

3.Remove belt cover.

4.Remove top two bolts securing auger housing to motor mount frame. Loosen bottom two bolts. See Figure 32.

1.Drain the gasoline from the fuel tank by removing the fuel line. Drain the gas and reinstall the fuel line.

,_ WARNING:fireorfrom Drainflame. the gasoline outdoors, away

Motor Mount

Frame

Remove Top Bolt (each side)

Bolts (Each Side)

Loosen bottom

Auge

Housing

Figure 32

5.Auger housing and motor mount frame will separate, hinged by bottom two bolts.

6.Loosen belt guide and pull away from auger drive pulley. See Figure 30.

7.Loosen the nut on the auger idler pulley and pull idler pulley away from the belt. Note location of idler pulley for later re-installation.

8.Remove belt from auger drive pulley.

9.Remove belt from impeller pulley.

10.Position new belt onto impeller pulley.

11.Position new belt onto auger drive pulley.

12.Adjust auger belt. (See Belt Adjustment).

13.Adjust belt guide. (See Belt Guide Adjustment in this sec- tion of the manual).

2.Disconnect spark plug wire.

3.Remove belt cover.

4.Remove top two bolts securing auger housing to motor mount frame. Loosen bottom two bolts. See Figure 32.

5.Auger housing and motor mount frame will separate, hinged by bottom two bolts.

6.Loosen the nut on the auger idler pulley and pull idler pulley away from the belt. Note location of idler pulley for later re-installation.

7.Loosen belt guide and pull away from auger drive pulley. See Figure 30.

8.Remove auger drive belt from auger pulley.

9.Pull traction drive belt idler pulley away from traction drive belt.

10.Remove traction drive belt.

11.Position new traction drive belt onto traction pulley.

12.Pull idler pulley away from belt, allowing belt to be posi- tioned onto auger pulley.

13.Release idler pulley. Ensure idler pulley is properly en- gaged with belt.

14.Reinstall auger drive belt.

15.Adjust auger belt. (See Belt Adjustment, in this section of the manual).

16.Adjust belt guide (see Belt Guide Adjustment in this sec- tion of the manual).

17.Replace top two bolts. Retighten bottom two bolts. See Figure 32.

18.Reinstall belt cover.

19.Reconnect the spark plug wire.

F-001008J

26

NEED PARTS? VISIT HTTP://WWW.MANUALBUDDY.COM/PARTS/

Page 25 Page 27
Image 26
Page 25 Page 27
Contents PrintedinU.S.A 001008J 12/13/99Sears Canada INC., TORONTO, Ontario M5B 2B8 Rules for Safe Operation PreparationMaintenance and Storage Wheeled Snow Blower Maintenance AgreementOwners Information Table of Contents Contents of Shipping Carton AssemblyTools Required for Assembly Parts Bags ContentsUnpacking Snow Chute Assembly Upper Handleand Crank Assembly Connect Control Cable SpringsSpeed Select Lever Remote Chute Control Knob Engine and Snow Blower Operating Controls Engine operating controls and their functions are as followsSnow Blower Operation Wheel Lock OUT PIN Fill GAS Temperature Type of OILBefore Starting Engine OOFWarm Engine Start Recoil Starter Minutes before blowing snow in temperatures below 0OFTo Start Engine Cold Engine Start Recoil StarterRemove finger from primer vent hole between USE of Electric StarterCold Engine Start Electric Starter See no TAG and Figure PushesWarm Engine Start Electric Starter Start EngineOperating Tips Recoil StarterProcedure Service RecommendationsService Recommendations After Each USEAS Required Customer ResponsibilitiesSnow Blower Lubrication AT StorageDisc Drive Plate Clean all excess greaseLubrication Every 25 Hours DiscEngine SAE Viscosity GradesTo Adjust Skid Height ADJUSTMENT/REPAIRAuger Housing Height Adjustment To Adjust Scraper BAR Auger Drive Belt Belt AdjustmentTraction Drive Belt Belt Replacement Auger Drive Belt see FigureBelt Guide Adjustment Cable Adjustment Traction Drive and Auger DriveFriction Wheel Adjustment If an adjustment is required, proceed as followsFriction Wheel Replacement Auger Shear Bolt Replacement Spark Plug Adjustment see FigureFireARNINGorflame.Drain gasoline outdoors, away from StorageOFF-SEASON Storage Trouble Shooting Chart Problem Look For RemedyDescription De piece Key No. NOsur ie SchemaDescriptionENGINE/ Moteur Drive COMPONENTS/ Batide Montagedu Moteur Key No. NOsur le SchemaDescription Drive COMPONENTS/ B.&,TIDE Montagedu Moteur108 111 109 140 Schema Description De pieceFrame Componentsi Bati 103 145 NOsur ieGear Casei BOiTER 340524 525 Auger Housingi VIS Sans FIN482 DISCHARGECHUTE/ DI=FLECTEURDE Goulotte 603Wheelsi Roue 673Headlighti Montagedu Phare 621 622 632 627 623 NOsurieHandle ! Poignie Sur le Controlpaneli Panneaude Commande HexnylSchema Description Electric Starter / ElectriqueChute ROD / Goulotte Tige 855862 850996 971 Remotechute CONTROL/ Diflecteurde Goulotte992 994 995 Decals / Autocollants 827 826282 NOsurie SchemaDescription Palier27915A Rf .27272A GL20A 37 0 RingNOsurie Schema Description Key No. No surie SchemaDescription RingOOIOO8J Serial No Blower Model DecalEngine Model Decal Service and Repair Parts Swars Swars Sears INC., TORONTO, Ontario M5B 2B8Conseils DE Securite Entretien ET Remisage Responsabilitis DU Client Avis AU ClientContrat Dentretien Garantie Limitie DE 2 ANS Pour LE CHASSE-NEIGE CraftsmanTables DES Matii RES Carton Dexpedition MontageOutils Requis Pour LE Montage SAC DE Pieces ContenantDfballage Montage DE LA Goulotte Branchement DES Cables DE Commande Montage DE LA Poignee Superieure ET DE LA ManivelleSgLECTEUR DE Vitesse Poignfe DE Commande DU Dfversoir Distance Levier de commande du ddflecteur b distance- Pousser Commandes DU Moteur ET DU CHASSE-NEIGEVoir Figure Les commandes du moteur et leurs fonctions sont UtilisationRouge Utilisation DU CHASSE-NEIGERemarque BlancGoupille DE Blocage DE Roue Niveaux DE Viscositi SAE Avant LA Mise EN Marche DU MoteurAvant Larrit Remplir DessenceMise EN Marche DU Moteur Chaud Mise EN Marche DU MoteurDemarreur .&.CORDE Utilisation DU Dfmarreur Flectrique Don de la prise residentielle dabord 001008JRemarque Un moteur chaud peut tre mis en marche Mise EN Marche DU Moteur Chaud DieMarreur Conseils Dutilisation Ddmarreur & cordeProcfdure Calendrier DentretienCalendrier Dentretien Apres Chaque UtilisationLubrification Avant Remisage CHASSE-NEIGEComme Requis Lubrification -TOUTES LES 10 HeuresLubrification Toutes LES 25 Heures Plateau de commande du disqueResponsabilites DE Client Pour lubrifierSauf MoteurRemarque Lhuile se vidange mieux Iorsquelle est chaude Pour rdgler les patins procdder comme suit REGLAGES/REPARATIONSRfglage DES Patins Courroie DE LA VIS Sans FIN Courroie DE Commande DES RouesReglage DES Courroies Remplacement DES Courroies Courroie DE LA VIS Sans FIN Voir FigureReglage DES Guide DE Courroie Voir Figure Rdglage ventuel voir FigureReglage DU Disque DE Friction Si un rdglage est ndcessaire, procdder comme suitRemplacement DU Disque DE Friction Remplacement DES Boulons DE Cisaillement DE LA VIS Sans FIN Remisage Remisage Hors SaisonTableau DE Diagnostic Problfme Cause RemfdeComment Obtenir DES PI#CES DE Rechange De srieEntretien ET Pieces DE Rechange Composez LE
Top Page Image Contents