Craftsman 536.8818 manual HOW to Replace the Belts, How To Remove the Auger Drive Belt

Page 24

[.,,."_o,,_ V_ZIIB]P'_"_

HOW TO REPLACE THE BELTS

The drive belts are of special construc- tion and must be replaced with original equipment replacement belts available from your nearest Sears service center.

Some steps require the assistance of a second person.

How To Remove the Auger Drive Belt

If the auger drive belt is damaged, the snow thrower will not discharge snow. Replace the damaged belt as follows.

1.Disconnect the spark plug wire.

2.Loosen the bolte on each side of the bottom panel (see Figure 27).

3.Remove the bottom panel.

Bolt Bottom

Panel

Auger

Housing

olt

Figure 27

4.Remove screw from belt cover. Remove the belt cover (see Figure 25).

5.Loosen the belt guide. Pull the belt guide away from the auger drive pulley (see Figure 29).

6.Pull the idler pulley away from the auger drive belt and slip the auger drive belt off of the idler pulley.

7.Remove the auger drive belt from the engine pulley. To remove the auger drive belt, the engine pulley may have to be partially rotated.

8.Remove the top four bolts that hold

together the auger housing and

 

the motor box. Loosen the bottom

 

F 0410108L

24

two bolts. The auger housing and the motor box can now be split apart for removal of the belt (see Figure 28).

9.Remove the old auger drive belt from the auger drive pulley. Re- place the auger drive belt with an original factory replacement belt available from an authorized service center (see Figure 29).

10.Install the new auger drive belt onto the auger drive pulley. NOTE: To assemble the auger housing to the motor box, have someone hold the auger clutch

lever in the ENGAGED position. This will move the idler arm and

pulley enough to allow the auger drive pulley to move back into position.

11.Assemble the auger housing to the motor box with the four bolts that

were removed in step 8. Tighten the bottom two bolts.

12.Install the auger drive belt onto the engine pulley.

13.Slip the auger drive belt under the idler pulley.

14.Adjust the auger drive belt. See "How To Adjust The Auger Drive

Belt" in the Service And Adjustment section.

15.Adjust the belt guide. See "How To Adjust The Belt Guide" in the Ser- vice And Adjustment section.

16.Install the belt cover. Tighten ecrew (See Figure 25).

17.Check the adjustment of the cables. See "How To Check And Adjust The Cables" in the Service And Adjust- ment section.

18.Install the bottom panel (see Figure 27).

19.Tighten the bolts on each side of the bottom panel.

20.Connect the spark plug wire.

Image 24
Contents Crrftsmrni Limited TWO-YEAR Warranty on Craftsman Snow Thrower IT MEANS--ATTENTIONBecome ALERTt!! Your Wash Hands After HandlingTraining PreparationOperation Maintenance and Storage Control and Operating SymbolsHandlesWalkneverrun Safety Warning Symbols StarterContents of Parts BAG Actual Size Assembly Tools Required forTo Remove Snow Thrower From CartonTo Assemble the Handle and Crank Assembly HOW to Assemble the Chute Deflector HOW to SET the Skid HeightHOW to SET the Length of the Cables Checklist Know Your Snow Thrower Auger Drive Lever Starts and stopsSpeed Shifter Lever Selects Electric Start Button if so equippedTo Stop Your Snow Thrower Can occurBefore Starting the Engine To Add OilFuels called gasohol or To Stop Engine Position. Backfire or engine damage can occurHow To Start a Cold Engine Der any conditionsHow To Start a Warm Engine Frozen StarterTo Remove Snow from Auger Snow Throwing TipsCompleteregular Hours Hours SeasonEngine Specifications Snow Thrower Power RatingsAuger Drive Belt Chain Lubrication Every 25 HoursEngine LubricationTo Adjust Skid Height To Adjust Scraper BARHeight adjustment skids, located on HOW to Remove Snow Hood Traction Drive Belt Auger Drive BeltRemove screw from belt cover. Remove belt cover see Figure HOW to Replace the Belts How To Remove the Auger Drive BeltLoosenBoltsiiiiiiii How To Remove Traction Drive Belt Remove the traction drive springPlate must SwingBelt Guide Adjustment HOW to Check Adjust the CablesAuger Drive Cable Adjustment Traction Drive Cable Adjustment Justment bracket until the Z hook can be removedRemove the bottom panel HOW to Adjust or Replace the Friction Wheel How To Check The Friction WheelSize How To Replace The Friction Wheel Erly installed in the original Make sure the washers areTion. Also, make sure the two Washers Are properly aligned With Actuator armsHOW to Replace Auger Shear Bolt Protect the machine, use Shear boltsOther HoUoIo To dischargeDefects Warranty Coverage Owners Warranty ResponsibilitiesSears Emission Control Defects Warranty Provisions California and United States EmissionFue!MeteringSystem Moderate \ \ Key Description Craftsman 8HP Snow Thrower Frame Craftsman 8HP Snow Thrower Gear Case 322Craftsman 8HP Snow Thrower Drive LF Axle Swing Plate YZ Craftsman 8HP Snow Thrower Discharge Chute Nylock Craftsman 8HP Snow Thrower Craftsman 8HP Snow Thrower Auger Housing Craftsman 8HP Snow Thrower Handle 31X.58X.08 Craftsman 8HP Snow Thrower Chute ROD Assembly Yoke ROD Craftsman 8HP Snow Thrower Shift Yoke 678 770 771772 7780410108L Briggs & Stratton Engine 742 615699510 399269694168 Piston 692786287 Assemblies include all parts shown in frames333 697929 334347 3562o¸i¸¸ 51.,=o692555 300318 5280410108L MANTENtMIENTO GARANTiA SiMBOLOSINTERNACIONALES Reparacinde AVERiAS100 Siempre desconectaCapacitacion PreparacionoperacionMantenimiento AlmacenamientoPerficies Sobre EL Nivel DEL Suelo SiMBOLOS DE Control Y Operacion Abajo Arriba Izquierda Derecha Importante PeligroContenido DE LA Bolsa DE Partes Tamaiio Real Como Sacar EL Quitanieves DE LA Caja Herramientas NecesariasTines de ajuste de altura, van suje Como Ensamblar EL Mango Y EL CON Junto DE LA Manivela Figura Perno ArandelaComo Ensamblar EL Deflector DEL Tubo DE DescargaApriete Demasiado C6MO Ajustar LOS Patines DE AlturaLista DE Revision Conozca SU Quitanieves Palanca de propulsi6n de la barrenaBoton de arranque electrico si la unidad Io Comodetenerel Quitanieves Comocontrolarla DescargadeComoavanzary Retroceder LanzamientodenieveAntesde Encenderel Motor CombustibleParadadelmotor ArranquedelmotorC6m0hacerarrancarel motorenfri0 La manija de arranque manual has Arranque CongeladoComoquitarla Nievey Escombrosatascadosdela Barrena Consejos Sobre EL Lanzamiento DE NieveResponsabilidades DEL Propietario Registrosde Servicio Recomendaciones GeneralesDespues DE Cada USO Motor Especificacionesquitanieves BarrenaLa placa del disco de propulsion Motor H, oC6MO Ajustar LOS Patines DE Altura Como Desmontar LA Instale la Ilave de 8eguridadAjuste DE LAS Correas C6MO Reemplazar LAS CORreas Correa de propulsionDe laba- rrena Retire Oaja del Motor AIojamiento de la barrena Como desmontar la correa de propulsion Conecte e! reeorte de propulsionNOTA. Si la tranemieion no fun Quite el reeorte de propulsionAjuste del cable de propulsi6n de la barrena FiguraAjustes DEL Cable DE Propulsion Jale el cable de propulsi6n per el eoporte de ajusteMin , pig C6MO Ajustar O Reemplazar LA Rueda DE FRICCI6N Como revisar la rueda de friccionPonga la palanca de cambio de Tamaro Ilanta DietanciaComo reemplazar la rueda de friccion Perno Alojamiento de la barrena 4. FiguraFigura Arandela Cojinetes Como Reemplazar LOS Pernos DE Seguridad DE LA Barrena QU Itani Eves MotorOtras Indicaciones Problema La unidad no se Puede propulsar a si mismaDescarga la nieve Responsabilidades del Propietario de la Garantia 0410108L Moderado ProlongadoYour Home