Craftsman 536.8818 HOW to Adjust or Replace the Friction Wheel, How To Check The Friction Wheel

Page 29

[.,,."_o,,_ F_IZIB]P'_"_

HOW TO ADJUST OR REPLACE THE FRICTION WHEEL

How To Check The Friction Wheel

If the snow thrower will not move for-

ward, check the traction drive belt, the traction drive cable or the friction wheel.

If the friction wheel is worn or damaged, it must be replaced. See "How To Re- place the Friction Wheel" in this section. If the friction wheel is not worn or dam-

aged, check as follows.

1.Run the engine until the fuel tank is empty and the engine stops.

2.Stand the snow thrower up on the front end of the auger housing (see Figure 37).

3.Disconnect the spark plug wire.

4.Loosen the bolts on each side of the bottom panel (see Figure 37).

5.Remove the bottom panel.

6.Position the shift speed lever in the lowest forward speed.

7.Note the position of the friction

wheel (see Figure 38). The correct distance "A" from the right side of the friction wheel to the outside of the motorbox is as follows:

Tire

Size

Distance

"A"

12

and 13 inch

4-1/8"

 

16

inch

4-5/16"

 

if the friction wheel is not in the correct position, adjust according to the fo!lowing instructions.

How To Adjust The Friction Wheel

1.Position the shift speed lever in the lowest forward speed.

2.Loosen the bolts on the speed control rod (see Figure 39).

3.Move the friction wheel to the cor- rect position (see Figure 38).

4.Tighten the bolts on the speed

control

rod (see Figure 39).

F 0410108L

29

5.Install the bottom panel (see Figure 37).

6.Tighten the bolts on each side of the bottom panel.

Bolt Bottom Panel

Auger

Housing

Figure 37

Figure 38

Speed Control Rod

Figure 39

Image 29
Contents Crrftsmrni IT MEANS--ATTENTION Limited TWO-YEAR Warranty on Craftsman Snow ThrowerBecome ALERTt!! Your Wash Hands After HandlingOperation TrainingPreparation HandlesWalkneverrun Maintenance and StorageControl and Operating Symbols Starter Safety Warning SymbolsContents of Parts BAG Actual Size Tools Required for AssemblyTo Remove Snow Thrower From CartonTo Assemble the Handle and Crank Assembly HOW to SET the Length of the Cables HOW to Assemble the Chute DeflectorHOW to SET the Skid Height Checklist Auger Drive Lever Starts and stops Know Your Snow ThrowerSpeed Shifter Lever Selects Electric Start Button if so equippedCan occur To Stop Your Snow ThrowerFuels called gasohol or Before Starting the EngineTo Add Oil Position. Backfire or engine damage can occur To Stop EngineDer any conditions How To Start a Cold EngineFrozen Starter How To Start a Warm EngineSnow Throwing Tips To Remove Snow from AugerHours Hours Season CompleteregularPower Ratings Engine Specifications Snow ThrowerAuger Drive Belt Chain Lubrication Every 25 HoursLubrication EngineHeight adjustment skids, located on To Adjust Skid HeightTo Adjust Scraper BAR HOW to Remove Snow Hood Remove screw from belt cover. Remove belt cover see Figure Traction Drive BeltAuger Drive Belt How To Remove the Auger Drive Belt HOW to Replace the BeltsLoosenBoltsiiiiiiii Remove the traction drive spring How To Remove Traction Drive BeltPlate must SwingAuger Drive Cable Adjustment Belt Guide AdjustmentHOW to Check Adjust the Cables Remove the bottom panel Traction Drive Cable AdjustmentJustment bracket until the Z hook can be removed Size HOW to Adjust or Replace the Friction WheelHow To Check The Friction Wheel How To Replace The Friction Wheel Make sure the washers are Erly installed in the originalTion. Also, make sure the two Washers Are properly aligned With Actuator armsProtect the machine, use Shear bolts HOW to Replace Auger Shear BoltOther To discharge HoUoIoOwners Warranty Responsibilities Defects Warranty CoverageSears Emission Control Defects Warranty Provisions California and United States EmissionFue!MeteringSystem Moderate \ \ Key Description Craftsman 8HP Snow Thrower Frame 322 Craftsman 8HP Snow Thrower Gear CaseCraftsman 8HP Snow Thrower Drive LF Axle Swing Plate YZ Craftsman 8HP Snow Thrower Discharge Chute Nylock Craftsman 8HP Snow Thrower Craftsman 8HP Snow Thrower Auger Housing Craftsman 8HP Snow Thrower Handle 31X.58X.08 Craftsman 8HP Snow Thrower Chute ROD Assembly Yoke ROD Craftsman 8HP Snow Thrower Shift Yoke 678 771 770772 7780410108L 742 615 Briggs & Stratton Engine399269 699510694168 Piston 692786Assemblies include all parts shown in frames 287334 333 697929347 3562o¸i¸¸ 300 51.,=o692555318 5280410108L SiMBOLOSINTERNACIONALES Reparacinde AVERiAS MANTENtMIENTO GARANTiA100 Siempre desconectaPreparacionoperacion CapacitacionPerficies Sobre EL Nivel DEL Suelo MantenimientoAlmacenamiento SiMBOLOS DE Control Y Operacion Importante Peligro Abajo Arriba Izquierda DerechaContenido DE LA Bolsa DE Partes Tamaiio Real Tines de ajuste de altura, van suje Como Sacar EL Quitanieves DE LA CajaHerramientas Necesarias Figura Perno Arandela Como Ensamblar EL Mango Y EL CON Junto DE LA ManivelaDEL Tubo DE Descarga Como Ensamblar EL DeflectorApriete Demasiado C6MO Ajustar LOS Patines DE AlturaLista DE Revision Boton de arranque electrico si la unidad Io Conozca SU QuitanievesPalanca de propulsi6n de la barrena Comocontrolarla Descargade Comodetenerel QuitanievesComoavanzary Retroceder LanzamientodenieveCombustible Antesde Encenderel MotorArranquedelmotor ParadadelmotorC6m0hacerarrancarel motorenfri0 Arranque Congelado La manija de arranque manual hasConsejos Sobre EL Lanzamiento DE Nieve Comoquitarla Nievey Escombrosatascadosdela BarrenaDespues DE Cada USO Responsabilidades DEL Propietario Registrosde ServicioRecomendaciones Generales La placa del disco de propulsion Motor EspecificacionesquitanievesBarrena H, o MotorC6MO Ajustar LOS Patines DE Altura Instale la Ilave de 8eguridad Como Desmontar LAC6MO Reemplazar LAS CO Ajuste DE LAS CorreasRreas Correa de propulsionDe laba- rrena Retire Oaja del Motor AIojamiento de la barrena Conecte e! reeorte de propulsion Como desmontar la correa de propulsionNOTA. Si la tranemieion no fun Quite el reeorte de propulsionFigura Ajuste del cable de propulsi6n de la barrenaMin , pig Ajustes DEL Cable DE PropulsionJale el cable de propulsi6n per el eoporte de ajuste Como revisar la rueda de friccion C6MO Ajustar O Reemplazar LA Rueda DE FRICCI6NPonga la palanca de cambio de Tamaro Ilanta DietanciaAlojamiento de la barrena 4. Figura Como reemplazar la rueda de friccion PernoFigura Arandela Cojinetes Como Reemplazar LOS Pernos DE Seguridad DE LA Barrena Otras Indicaciones QU Itani EvesMotor Descarga la nieve ProblemaLa unidad no se Puede propulsar a si misma Responsabilidades del Propietario de la Garantia 0410108L Prolongado ModeradoYour Home