Craftsman 536.8818 manual Belt Guide Adjustment, HOW to Check Adjust the Cables

Page 27

[.,,."_o,,_ V_ZIIB]P'_"_

BELT GUIDE ADJUSTMENT

"Z" Fitting

1.Remove spark plug wire.

2.Have someone engage auger drive.

3.Measure the distance between the belt guide and belt. The distance should be 1/8 inch (3.175 mm) for guide. See Figure 31.

l

_

..i"

Belt Guide

 

 

 

 

 

\ u

1/8 Inch

-......-\\""(3.175)

?-\\

Engaged i o_

Figure 31

4.If adjustment is necessary, loosen belt guide mounting bolt. Move belt guide to the correct position. Tight- en mounting bolt.

5.Reinstall belt cover.

6.Reconnect spark plug wire.

Figure 32

The center of the "Z" fitting should be between the center and top of the hole in the clutch lever. Adjust either the auger drive cable or the traction drive cable as as necessary

according to the following instruc- tions.

Auger Drive Cable Adjustment

1.Run the engine until the fuel tank is empty and the engine stops.

2.Stand the snow thrower up on the front end of the auger housing.

3.Push cable through spring to ex- pose the threaded portion of the cable (see Figure 33).

HOW TO CHECK AND

ADJUST THE CABLES

The cables are adjusted at the factory and no adjustment should be neces- sary. If the cables have become stretched or are sagging adjustment will be necessary.

Whenever belts are adjusted or re- placed, the cables will need to be ad- justed.

To check for correct adjustment, un-

hook "Z" fitting at clutch lever (see

Figure 32).

1.Move clutch lever to the full forward position (just contacting plastic

bumper). Holding cable tight, note

position of fitting to hole in clutch le-

 

ver.

 

F 0410108L

27

Square

End _,

Cable Spring

Locknut

Figure 33

Hold square end of threaded portion with pliers and adjust Iocknut in or out until correct adjustment is reached. Pull cable back through spring and connect cable.

Image 27
Contents Crrftsmrni Wash Hands After Handling Limited TWO-YEAR Warranty on Craftsman Snow ThrowerIT MEANS--ATTENTION Become ALERTt!! YourTraining PreparationOperation Maintenance and Storage Control and Operating SymbolsHandlesWalkneverrun Starter Safety Warning SymbolsContents of Parts BAG Actual Size From Carton AssemblyTools Required for To Remove Snow ThrowerTo Assemble the Handle and Crank Assembly HOW to Assemble the Chute Deflector HOW to SET the Skid HeightHOW to SET the Length of the Cables Checklist Electric Start Button if so equipped Know Your Snow ThrowerAuger Drive Lever Starts and stops Speed Shifter Lever SelectsCan occur To Stop Your Snow ThrowerBefore Starting the Engine To Add OilFuels called gasohol or Position. Backfire or engine damage can occur To Stop EngineDer any conditions How To Start a Cold EngineFrozen Starter How To Start a Warm EngineSnow Throwing Tips To Remove Snow from AugerHours Hours Season CompleteregularChain Lubrication Every 25 Hours Engine Specifications Snow ThrowerPower Ratings Auger Drive BeltLubrication EngineTo Adjust Skid Height To Adjust Scraper BARHeight adjustment skids, located on HOW to Remove Snow Hood Traction Drive Belt Auger Drive BeltRemove screw from belt cover. Remove belt cover see Figure How To Remove the Auger Drive Belt HOW to Replace the BeltsLoosenBoltsiiiiiiii Swing How To Remove Traction Drive BeltRemove the traction drive spring Plate mustBelt Guide Adjustment HOW to Check Adjust the CablesAuger Drive Cable Adjustment Traction Drive Cable Adjustment Justment bracket until the Z hook can be removedRemove the bottom panel HOW to Adjust or Replace the Friction Wheel How To Check The Friction WheelSize How To Replace The Friction Wheel Washers Are properly aligned With Actuator arms Erly installed in the originalMake sure the washers are Tion. Also, make sure the twoProtect the machine, use Shear bolts HOW to Replace Auger Shear BoltOther To discharge HoUoIoCalifornia and United States Emission Defects Warranty CoverageOwners Warranty Responsibilities Sears Emission Control Defects Warranty ProvisionsFue!MeteringSystem Moderate \ \ Key Description Craftsman 8HP Snow Thrower Frame 322 Craftsman 8HP Snow Thrower Gear CaseCraftsman 8HP Snow Thrower Drive LF Axle Swing Plate YZ Craftsman 8HP Snow Thrower Discharge Chute Nylock Craftsman 8HP Snow Thrower Craftsman 8HP Snow Thrower Auger Housing Craftsman 8HP Snow Thrower Handle 31X.58X.08 Craftsman 8HP Snow Thrower Chute ROD Assembly Yoke ROD Craftsman 8HP Snow Thrower Shift Yoke 678 778 770771 7720410108L 742 615 Briggs & Stratton Engine692786 699510399269 694168 PistonAssemblies include all parts shown in frames 287356 333 697929334 3472o¸i¸¸ 528 51.,=o692555300 3180410108L Siempre desconecta MANTENtMIENTO GARANTiASiMBOLOSINTERNACIONALES Reparacinde AVERiAS 100Preparacionoperacion CapacitacionMantenimiento AlmacenamientoPerficies Sobre EL Nivel DEL Suelo SiMBOLOS DE Control Y Operacion Importante Peligro Abajo Arriba Izquierda DerechaContenido DE LA Bolsa DE Partes Tamaiio Real Como Sacar EL Quitanieves DE LA Caja Herramientas NecesariasTines de ajuste de altura, van suje Figura Perno Arandela Como Ensamblar EL Mango Y EL CON Junto DE LA ManivelaC6MO Ajustar LOS Patines DE Altura Como Ensamblar EL DeflectorDEL Tubo DE Descarga Apriete DemasiadoLista DE Revision Conozca SU Quitanieves Palanca de propulsi6n de la barrenaBoton de arranque electrico si la unidad Io Lanzamientodenieve Comodetenerel QuitanievesComocontrolarla Descargade Comoavanzary RetrocederCombustible Antesde Encenderel MotorArranquedelmotor ParadadelmotorC6m0hacerarrancarel motorenfri0 Arranque Congelado La manija de arranque manual hasConsejos Sobre EL Lanzamiento DE Nieve Comoquitarla Nievey Escombrosatascadosdela BarrenaResponsabilidades DEL Propietario Registrosde Servicio Recomendaciones GeneralesDespues DE Cada USO Motor Especificacionesquitanieves BarrenaLa placa del disco de propulsion H, o MotorC6MO Ajustar LOS Patines DE Altura Instale la Ilave de 8eguridad Como Desmontar LACorrea de propulsion Ajuste DE LAS CorreasC6MO Reemplazar LAS CO RreasDe laba- rrena Retire Oaja del Motor AIojamiento de la barrena Quite el reeorte de propulsion Como desmontar la correa de propulsionConecte e! reeorte de propulsion NOTA. Si la tranemieion no funFigura Ajuste del cable de propulsi6n de la barrenaAjustes DEL Cable DE Propulsion Jale el cable de propulsi6n per el eoporte de ajusteMin , pig Tamaro Ilanta Dietancia C6MO Ajustar O Reemplazar LA Rueda DE FRICCI6NComo revisar la rueda de friccion Ponga la palanca de cambio deAlojamiento de la barrena 4. Figura Como reemplazar la rueda de friccion PernoFigura Arandela Cojinetes Como Reemplazar LOS Pernos DE Seguridad DE LA Barrena QU Itani Eves MotorOtras Indicaciones Problema La unidad no se Puede propulsar a si mismaDescarga la nieve Responsabilidades del Propietario de la Garantia 0410108L Prolongado ModeradoYour Home