Sanyo PDG-DXL100 owner manual Order Replacement Lamp

Page 48

Appendices

ORDER REPLACEMENT LAMP

Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer.

Model No. of your projector : PDG-DXL100

Replacement Lamp Type No. : POA-LMP138

(Service Parts No. 610 346 4633)

LAMP HANDLING PRECAUTIONS

This projector uses a high-pressure lamp which must be handled carefully and properly.

Improper handling may result in accidents, injury, or create a fire hazard.

Lamp life may differ from lamp to lamp and according to the environment of use. There is no guarantee of the same life for each lamp. Some lamps may fail or terminate their life in a shorter period of time than other similar lamps.

If the projector indicates that the lamp should be replaced, i.e., if the lamp life warning message appears, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow carefully the instructions in the Lamp Re- placement section of this manual.) Continuous use of the lamp with showing the lamp life warning message may increase the risk of lamp explosion.

A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used.

IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.

If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immedi- ately. Contact an authorized service station for a checkup of the unit and replace- ment of the lamp. Additionally, check carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector except those who are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken glass.

47

English

English

Image 48
Contents Model PDG-DXL100 Table of Contents Precautions Usage NoticeRear Do not Product Features IntroductionPackage Overview NotProduct Overview ProjectorConnection Ports Control PanelRemote Control Refer to the Power On/Off the ProJector section. See pages 15~16 Confirm your section of items in subImage Volume + Remote Control Battery Installation Remote Control Operating RangeConnecting the Projector Connect to Computer/NotebookConnect to Video Powering On/Off the Projector Powering On the ProjectorLens Cap Power Powering Off the Projector Installation Adjusting the Projected Image Adjusting the Height of Projector ImageAdjusting the Projector Focus Adjusting Projection Image SizeHow to operate On Screen DisplayImage Mode BrightnessContrast Total DotsFine Sync White PeakingColor Temp GammaImage Video Mode ColorTint SharpnessKeystone Position Horizontal PositionPosition Vertical Position Aspect RatioMounting ECO Mode RS232 ModeInput Search Fan ControlEco Standby Power 1W Remote ControlPower Management Closed CaptionLamp Counter Reset Security SettingsFactory Default Network Status IP AddressSubnet Mask GatewayLanguage InformationConfiguring the Network Setting Controlling the Projector From WebClick Use the following IP address, and type in as below User Controls Home How to operate Control Panel Network Setting Projector SettingNetwork Setting Password SettingSecurity Setting Telnet Password SettingPJLink Password Setting Alert Setting Email SettingSmtp Setting Alert ConditionLogout Troubleshooting Problem No image appears on screenProblem Partial, scrolling or incorrectly displayed image Problem Image is unstable or flickering IBM=Problem Image is out of focus Problem The image is stretched when displaying 169 DVDProblem Image is reversed Problem Lamp burns out or makes a popping soundProblem LED lighting message POWER-LED Temp LampProblem Message Reminders Lamp Replacing Procedure Replacing the lampOrder Replacement Lamp Cleaning the Air Filters Air Filters Cleaning ProcedureSpecifications NTSC-M/NTSC-4.43/PAL-B, D, G, H, I/PAL-M/PAL-N/SECAMModes Resolution Frequency KHz Computer Compatibility AnalogComputer Compatibility Digital- Hdmi Modes Resolution Frequency Configurations of Terminals Terminal Analog RGB Mini D-sub 15 pinTerminal Mini DIN 8-pin Regulation & Safety Notices FCC noticeRemarque à l’intention des utilisateurs cana- diens Serial Control Interface OperationFunctional Execution Command FormatStatus Read Command Use of Telnet ControlPJLink Notice Dimensions Lens CenterKF8A