Hitachi CP-X600 user manual Power on/off, Turning on the power, Turning off the power

Page 15

Power on/off

Power on/off

Turning on the power

1. Make sure that the power cord is firmly and correctly connected to the projector and the outlet.

2. Remove the lens cover, and set the power switch to the ON position.

The power indicator will light up in steady orange (58). Then wait several seconds because the buttons may not function for these several seconds.

STANDBY/ON button

POWER indicator

(1) When AUTO ON in OPTION menu is set to TURN ON (41) : The lamp will only be automatically turned on when the Power switch is turned on after the power was turned off by Power switch last time. Afterwards the POWER indicator will begin blinking in green. When the power is completely on, the indicator will stop blinking and light in green.

(2) When AUTO ON in the OPTION menu is set to TURN OFF

(41): Please see step 3.

3. Press the STANDBY/ON button on the projector or the remote control.

To display the picture, select an input signal according to the section "Selecting an input signal" (16).

POWER

(Steady orange)

POWER

(Blinking in green)

POWER

(Steady green)

Turning off the power

Press the STANDBY/ON button on the projector or the remote

 

1. control.

Power off?

The message "Power off?" will appear on the screen for about 5

 

seconds.

POWER

Press the STANDBY/ON button on the projector or the remote

 

2. control again while the message appears.

(Blinking in orange)

The projector lamp will go off, and the POWER indicator will begin

 

blinking in orange.

POWER

 

Then the POWER indicator will stop blinking and light in steady

(Steady orange)

orange when the lamp cooling is complete.

 

3. Make sure that the power indicator lights in steady orange, and set the power switch to the OFF position. The POWER indicator will go off. Attach the lens cover.

Do not turn the projector on for 10 minutes or more after turning it off. Turning the projector on again too soon could shorten the lifetime of some consumable parts of the projector.

WARNING ►A strong light is emitted when the projector’s power is on. Do not look into the lens of the projector or look inside of the projector through any of the projector’s openings. ►Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot.

NOTE • Turn the power on/off in right order. Please power on the projector prior to the connected devices. Power off the projector later than the connected devices.

• Use the shutdown switch (60) only when the projector is not turned off by normal procedure.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Content Fastening the lens cover Contents of packageHOT Part namesProjector HOT!4Audio IN4 R/L ports 10 RGB OUT port 10 Audio OUT port 10 Control panelRear panel CB/PB, CR/PR ports 10Back Remote control Remote controlSetting up Down ArrangementOn a horizontal surface Suspended from the ceilingFoot Adjusting the projectors elevatorUsing the security bar and slot Security bar Anti-theft chain or wire Security slotSpeakers VCR/DVD player Connecting your devicesAbout Plug-and-Play capability Connecting your devicesAC inlet Connector of the power cord to the outlet Connecting power supplyPutting batteries Remote controlBack sensor About the remote control signalChanging the frequency of remote control signal Front and top sensorsWhen Auto on in the Option menu is set to Turn OFF Power on/offTurning on the power Turning off the powerTemporarily muting the sound Adjusting the volumeSelecting an input signal Operating For no signal Searching an input signalSelecting an input signal  For an RGB signal For a component video signal Adjusting the zoom and focusUsing the automatic adjustment feature  For a video signal or s-video signalCorrecting the keystone distortions Adjusting the positionFreezing the screen Using the magnify featureTemporarily blanking the screen Using the menu function Easy MenuAdvanced Menu Easy Menu Easy Menu Gamma Picture MenuColor Temp Using the / buttons switches the color temperature modePicture Menu Custom and then pressing the button orSAVE1, SAVE2, SAVE3, SAVE4 Active IrisLOAD1, LOAD2, LOAD3, LOAD4 MY MemoryOver Scan For an RGB signalFor no signal Image MenuSize PhaseAuto Adjust Image MenuColor Space Input MenuProgressive 3D-YCSInput Menu ComponentVideo Format Frame Lock Custom Resolution BOX ResolutionFunction may not work well Setup MenuSome input, this function may not work well Function may not work correctlySetup Menu Audio VolumeAudio Menu SpeakerOr keep no operation for about 10 seconds Using the /// buttons adjusts the menu positionUsing the / buttons switches the mode for the blank screen Screen MenuStart UP Screen MenuCapturing error has occurred. Please try again MyScreenMyScreen registration is finished Message Option Menu Auto SearchAuto on Option Menu Auto OFFLamp Time Service MY ButtonFAN Speed Filter Message GhostRemote Freq Factory ResetKEY Lock Remote ReceivUsing Security Features Inputting the PasswordSecurity Setting the Password Using the MyScreen Password FunctionDescription If you have forgotten your Password Turning on the MyScreen PasswordUsing the PIN Lock Function Turning the Password offRegistering the PIN Code If you have forgotten your PIN Code Turning Off the PIN Lock FunctionUsing the Transition Detector Function Setting the Transition Detector PasswordTurning On the Transition Detector Function Security Setting the Transition Detector offType number = DT00771 Replacing the lamp MaintenanceCase of replacement by yourself LampLamp Air filter Type number = MU03642 Cleaning the air filterAir filter Page Related messages TroubleshootingThere is no input signal Internal temperature is risingRegarding the indicator lamps Regarding the indicator lamps Signal source does not correctly work Electrical power cord is not pluggedPower switch is not set to the on position Signal cables are not correctly connectedColor Space setting is not suitable Volume is adjusted to an extremely low levelAudio setting is not correct Color settings are not correctly adjustedLamp is approaching the end of its product Lifetime Not properly adjustedEither the focus and/or horizontal phase settings are Whisper function is workingSpecification Warranty and after-serviceSpecifications
Top Page Image Contents