Hitachi CP-X600 Whisper function is working, Lamp is approaching the end of its product Lifetime

Page 62

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects (continued)

Phenomenon

Cases not involving a machine defect

Reference

page

 

 

 

 

 

 

The brightness and/or contrast are adjusted to an

 

 

extremely low level.

24, 25

 

Adjust BRIGHTNESS and/or CONTRAST settings to a

 

 

 

higher level using the menu function.

 

Pictures appear

The WHISPER function is working.

 

dark.

Select NORMAL for the WHISPER item in the SETUP

24, 35

 

menu.

 

 

The lamp is approaching the end of its product

 

 

lifetime.

52, 53

 

Replace the lamp.

 

 

Either the focus and/or horizontal phase settings are

 

 

not properly adjusted.

18, 29

Pictures appear

Adjust the focus using the focus ring, and/or H PHASE

 

blurry.

using the menu function.

 

 

The lens is dirty or misty.

56

 

Clean the lens referring to the section “Caring for the lens”.

 

 

Pictures are

The exhaust ventilation holes at front is blocked by

 

some objects.

4

trembling.

Remove any objects from front side of the projector.

 

 

 

NOTE • Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and it does not constitute or imply a machine defect.

62

Page 61 Page 63
Image 62
Page 61 Page 63
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Content Contents of package Fastening the lens coverHOT!4 Part namesProjector HOTCB/PB, CR/PR ports 10 Control panelRear panel Audio IN4 R/L ports 10 RGB OUT port 10 Audio OUT port 10Remote control Back Remote controlSetting up Suspended from the ceiling ArrangementOn a horizontal surface DownSecurity bar Anti-theft chain or wire Security slot Adjusting the projectors elevatorUsing the security bar and slot FootConnecting your devices Speakers VCR/DVD playerConnecting your devices About Plug-and-Play capabilityConnecting power supply AC inlet Connector of the power cord to the outletRemote control Putting batteriesFront and top sensors About the remote control signalChanging the frequency of remote control signal Back sensorTurning off the power Power on/offTurning on the power When Auto on in the Option menu is set to Turn OFFOperating Adjusting the volumeSelecting an input signal Temporarily muting the sound For an RGB signal Searching an input signalSelecting an input signal  For no signal For a video signal or s-video signal Adjusting the zoom and focusUsing the automatic adjustment feature  For a component video signalAdjusting the position Correcting the keystone distortionsUsing the magnify feature Freezing the screenTemporarily blanking the screen Advanced Menu Using the menu functionEasy Menu Easy Menu Easy Menu Picture Menu GammaCustom and then pressing the button or Using the / buttons switches the color temperature modePicture Menu Color TempMY Memory Active IrisLOAD1, LOAD2, LOAD3, LOAD4 SAVE1, SAVE2, SAVE3, SAVE4Image Menu For an RGB signalFor no signal Over ScanImage Menu PhaseAuto Adjust Size3D-YCS Input MenuProgressive Color SpaceVideo Format Input MenuComponent Frame Lock Resolution Custom Resolution BOXFunction may not work correctly Setup MenuSome input, this function may not work well Function may not work wellSetup Menu Speaker VolumeAudio Menu AudioScreen Menu Using the /// buttons adjusts the menu positionUsing the / buttons switches the mode for the blank screen Or keep no operation for about 10 secondsScreen Menu Start UPMyScreen registration is finished Capturing error has occurred. Please try againMyScreen Message Auto on Option MenuAuto Search Lamp Time Option MenuAuto OFF FAN Speed ServiceMY Button Ghost Filter MessageRemote Receiv Factory ResetKEY Lock Remote FreqSecurity Using Security FeaturesInputting the Password Turning on the MyScreen Password Using the MyScreen Password FunctionDescription If you have forgotten your Password Setting the PasswordRegistering the PIN Code Using the PIN Lock FunctionTurning the Password off Turning Off the PIN Lock Function If you have forgotten your PIN CodeTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password Setting the Transition Detector off SecurityLamp MaintenanceCase of replacement by yourself Type number = DT00771 Replacing the lampLamp Type number = MU03642 Cleaning the air filter Air filterAir filter Page Internal temperature is rising TroubleshootingThere is no input signal Related messagesRegarding the indicator lamps Regarding the indicator lamps Signal cables are not correctly connected Electrical power cord is not pluggedPower switch is not set to the on position Signal source does not correctly workColor settings are not correctly adjusted Volume is adjusted to an extremely low levelAudio setting is not correct Color Space setting is not suitableWhisper function is working Not properly adjustedEither the focus and/or horizontal phase settings are Lamp is approaching the end of its product LifetimeWarranty and after-service SpecificationSpecifications
Top Page Image Contents