Hitachi CP-X600 user manual Lamp

Page 53

Maintenance

Lamp (continued)

WARNING

HIGH VOLTAGE

 

HIGH TEMPERATURE

HIGH PRESSURE

 

►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

►About disposal of a lamp • This product contains a mercury lamp; do not put it in a trash. Dispose of it in accordance with environmental laws.

For lamp recycling, go to www.lamprecycle.org. (in the US)

For product disposal, contact your local government agency or www.eiae.org (in the US) or www.epsc.ca (in Canada).

For more information, call your dealer.

• If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the inside of the projector, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.

Disconnect • If the lamp should break (it will make a loud bang when it does),

the plug

ventilate the room well, and make sure not to breathe the gas that

from the

comes out of the projector vents, or get it in your eyes or mouth.

power

• Before replacing the lamp, turn the projector off and unplug the power

outlet

cord, then wait at least 45 minutes for the lamp to cool sufficiently.

 

Handling the lamp while hot can cause burns, as well as damaging the

 

lamp.

•Never unscrew except the appointed (marked by an arrow) screws.

•Do not open the lamp cover while the projector is suspended from the ceiling. This is dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken.

•Do not use the projector with the lamp cover removed. To replace the lamp, make sure that the screws are tightened firmly. Loose screws could result in damage or injury.

•Use only the lamp of the specified type.

•If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, contact your local dealer or a service representative.

•Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

•Using the lamp for long periods of time, could cause it dark, not to light up or to burst. When the pictures appear dark, or when the color tone is poor, please replace the lamp as soon as possible. Do not use old (used) lamps; this is a cause of breakage.

53

Page 52 Page 54
Image 53
Page 52 Page 54
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Content Fastening the lens cover Contents of packageProjector Part namesHOT!4 HOTRear panel Control panelCB/PB, CR/PR ports 10 Audio IN4 R/L ports 10 RGB OUT port 10 Audio OUT port 10Back Remote control Remote controlSetting up On a horizontal surface ArrangementSuspended from the ceiling DownUsing the security bar and slot Adjusting the projectors elevatorSecurity bar Anti-theft chain or wire Security slot FootSpeakers VCR/DVD player Connecting your devicesAbout Plug-and-Play capability Connecting your devicesAC inlet Connector of the power cord to the outlet Connecting power supplyPutting batteries Remote controlChanging the frequency of remote control signal About the remote control signalFront and top sensors Back sensorTurning on the power Power on/offTurning off the power When Auto on in the Option menu is set to Turn OFFSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundSelecting an input signal Searching an input signal For an RGB signal  For no signalUsing the automatic adjustment feature Adjusting the zoom and focus For a video signal or s-video signal  For a component video signalCorrecting the keystone distortions Adjusting the positionFreezing the screen Using the magnify featureTemporarily blanking the screen Advanced Menu Using the menu functionEasy Menu Easy Menu Easy Menu Gamma Picture MenuPicture Menu Using the / buttons switches the color temperature modeCustom and then pressing the button or Color TempLOAD1, LOAD2, LOAD3, LOAD4 Active IrisMY Memory SAVE1, SAVE2, SAVE3, SAVE4For no signal For an RGB signalImage Menu Over ScanAuto Adjust PhaseImage Menu SizeProgressive Input Menu3D-YCS Color SpaceVideo Format Input MenuComponent Frame Lock Custom Resolution BOX ResolutionSome input, this function may not work well Setup MenuFunction may not work correctly Function may not work wellSetup Menu Audio Menu VolumeSpeaker AudioUsing the / buttons switches the mode for the blank screen Using the /// buttons adjusts the menu positionScreen Menu Or keep no operation for about 10 secondsStart UP Screen MenuMyScreen registration is finished Capturing error has occurred. Please try againMyScreen Message Auto on Option MenuAuto Search Lamp Time Option MenuAuto OFF FAN Speed ServiceMY Button Filter Message GhostKEY Lock Factory ResetRemote Receiv Remote FreqSecurity Using Security FeaturesInputting the Password Description If you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Setting the PasswordRegistering the PIN Code Using the PIN Lock FunctionTurning the Password off If you have forgotten your PIN Code Turning Off the PIN Lock FunctionTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password Security Setting the Transition Detector offCase of replacement by yourself MaintenanceLamp Type number = DT00771 Replacing the lampLamp Air filter Type number = MU03642 Cleaning the air filterAir filter Page There is no input signal TroubleshootingInternal temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps Power switch is not set to the on position Electrical power cord is not pluggedSignal cables are not correctly connected Signal source does not correctly workAudio setting is not correct Volume is adjusted to an extremely low levelColor settings are not correctly adjusted Color Space setting is not suitableEither the focus and/or horizontal phase settings are Not properly adjustedWhisper function is working Lamp is approaching the end of its product LifetimeSpecification Warranty and after-serviceSpecifications
Top Page Image Contents