Hitachi CP-X600 user manual Option Menu, Auto Search, Auto on

Page 41

OPTION Menu

OPTION Menu

From the OPTION menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or remote control, or ENTER button on the remote control to execute the item, except for the items LAMP TIME and FILTER TIME. Then perform it according to the following table.

/'07=4)$?

5'.'%6

2+%674'

#7615'#4%*67401((

+/#)'

#761-';5610'67401((

+0276

#7611067401((

5'672

#7611((OKP

#7&+1

.#/26+/'J

5%4''0

(+.6'46+/'J

126+10

/;$76610

'#5;/'07

5'48+%'

 

5'%74+6;

Item

Description

 

Using the ▲/▼ buttons turns on/off the automatic signal search function.

 

TURN ON TURN OFF

 

When the TURN ON is selected, detecting no signal automatically cycles

AUTO SEARCH

through input ports in the following order. The search is started from the

current port. Then when an input is found, the projector will stop searching

 

 

and display the image.

 

RGB 1 RGB 2 COMPONENT S-VIDEO VIDEO

 

 

 

Using the ▲/▼ buttons turns on/off the automatic keystone function.

 

TURN ON TURN OFF

 

TURN ON : Automatic keystone distortion correction will be

 

executed whenever changing the slant of the projector.

AUTO

TURN OFF : This function is disabled. Please execute the AUTO

KEYSTONE

KEYSTONE EXECUTE in the SETUP Menu for automatic

 

keystone distortion correction.

 

• When the projector is suspended from the ceiling this feature will

 

not function properly so select the TURN OFF.

 

• This function will be unavailable when the Transition Detector is

 

on (50).

 

Using the ▲/▼ buttons turns on/off the AUTO ON function.

 

TURN ON TURN OFF

 

When AUTO ON is set to TURN ON, the projector’s lamp will only

AUTO ON

be automatically turned on when the Power switch is turned on if

the power was turned off using the Power switch the last time the

 

projector was turned off.

 

• After turning the lamp on by the AUTO ON function, if neither input nor

 

operation is detected for about 30 minutes, the projector is turned off, even

 

though the AUTO OFF function (42) is disabled.

(continued on next page)

41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Content Fastening the lens cover Contents of packageProjector Part namesHOT!4 HOTRear panel Control panelCB/PB, CR/PR ports 10 Audio IN4 R/L ports 10 RGB OUT port 10 Audio OUT port 10Back Remote control Remote controlSetting up On a horizontal surface ArrangementSuspended from the ceiling DownUsing the security bar and slot Adjusting the projectors elevatorSecurity bar Anti-theft chain or wire Security slot FootSpeakers VCR/DVD player Connecting your devicesAbout Plug-and-Play capability Connecting your devicesAC inlet Connector of the power cord to the outlet Connecting power supplyPutting batteries Remote controlChanging the frequency of remote control signal About the remote control signalFront and top sensors Back sensorTurning on the power Power on/offTurning off the power When Auto on in the Option menu is set to Turn OFFSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundSelecting an input signal Searching an input signal For an RGB signal  For no signalUsing the automatic adjustment feature Adjusting the zoom and focus For a video signal or s-video signal  For a component video signalCorrecting the keystone distortions Adjusting the positionFreezing the screen Using the magnify featureTemporarily blanking the screen Advanced Menu Using the menu functionEasy Menu Easy Menu Easy Menu Gamma Picture MenuPicture Menu Using the / buttons switches the color temperature modeCustom and then pressing the button or Color TempLOAD1, LOAD2, LOAD3, LOAD4 Active IrisMY Memory SAVE1, SAVE2, SAVE3, SAVE4For no signal For an RGB signalImage Menu Over ScanAuto Adjust PhaseImage Menu SizeProgressive Input Menu3D-YCS Color SpaceVideo Format Input MenuComponent Frame Lock Custom Resolution BOX ResolutionSome input, this function may not work well Setup MenuFunction may not work correctly Function may not work wellSetup Menu Audio Menu VolumeSpeaker AudioUsing the / buttons switches the mode for the blank screen Using the /// buttons adjusts the menu positionScreen Menu Or keep no operation for about 10 secondsStart UP Screen MenuMyScreen registration is finished Capturing error has occurred. Please try againMyScreen Message Auto on Option MenuAuto Search Lamp Time Option MenuAuto OFF FAN Speed ServiceMY Button Filter Message GhostKEY Lock Factory ResetRemote Receiv Remote FreqSecurity Using Security FeaturesInputting the Password Description If you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Setting the PasswordRegistering the PIN Code Using the PIN Lock FunctionTurning the Password off If you have forgotten your PIN Code Turning Off the PIN Lock FunctionTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password Security Setting the Transition Detector offCase of replacement by yourself MaintenanceLamp Type number = DT00771 Replacing the lampLamp Air filter Type number = MU03642 Cleaning the air filterAir filter Page There is no input signal TroubleshootingInternal temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps Power switch is not set to the on position Electrical power cord is not pluggedSignal cables are not correctly connected Signal source does not correctly workAudio setting is not correct Volume is adjusted to an extremely low levelColor settings are not correctly adjusted Color Space setting is not suitableEither the focus and/or horizontal phase settings are Not properly adjustedWhisper function is working Lamp is approaching the end of its product LifetimeSpecification Warranty and after-serviceSpecifications
Top Page Image Contents