Hitachi CP-X600 user manual Turning Off the PIN Lock Function, If you have forgotten your PIN Code

Page 49

OPTION Menu

2+0$1:

+PRWV2+0%QFG

4)$

PIN BOX

2+0$1:

%QPHKTOCVKQP

4)$

CONFIRMATION BOX

(PIN BOX)

OPTION Menu (continued)

Item

Description

SECURITY

3.1-3 Input a 4 part PIN Code using the ▲/▼/◄/►

/RGB and INPUT buttons. A CONFIRMATION BOX will appear. Reenter the

same PIN Code. This will complete the PIN Code registration.

NOTE: If there is no key input for about 55 seconds while the PIN BOX or the CONFIRMATION BOX are displayed the menu will close. If necessary repeat the process from 3.1-1.

Afterwards, anytime the projector is restarted after

the power switch is turned off the PIN BOX will be displayed. Enter the registered PIN Code.

The projector can be used after entering the registered PIN Code. If an incorrect PIN Code is input the PIN BOX will be displayed again.

If an incorrect PIN Code is input 3 times the projector will turn off. Afterwards the projector will turn off every time an incorrect PIN Code is input. The projector will also turn off if there is no key input for about 5 minutes while the PIN BOX is displayed.

This function will activate only when the projector is started after the power switch was turned off.

•Please do not forget your PIN Code.

3.2 Turning Off the PIN LOCK Function

3.2-1 Follow the procedure in 3.1-1 to display the PIN LOCK on/off menu. Use the ▲/▼ buttons to select TURN OFF and the PIN BOX will be displayed.

Enter the registered PIN Code to turn the PIN LOCK function off. If an incorrect PASSWORD is entered the menu will close.

3.3 If you have forgotten your PIN Code

3.3-1 While the PIN BOX is displayed, press and hold the RESET button for three seconds or press and hold the INPUT and ► buttons for three seconds. The 10 digit Inquiring Code will be displayed.

NOTE: If there is no key input for about 5 minutes while the Inquiring Code is displayed the projector will turn off.

2+0$1:

+PSWKTKPI%QFG

Inquiring Code

(PIN Code)

3.3-2 Contact your dealer with the 10 digit Inquiring Code. Your PASSWORD will be sent after your user registration information is confirmed.

(continued on next page)

49

Image 49

Contents Thank you for purchasing this projector About this manualTrademark acknowledgment Content Fastening the lens cover Contents of packageProjector Part namesHOT!4 HOTRear panel Control panelCB/PB, CR/PR ports 10 Audio IN4 R/L ports 10 RGB OUT port 10 Audio OUT port 10Back Remote control Remote controlSetting up On a horizontal surface ArrangementSuspended from the ceiling DownUsing the security bar and slot Adjusting the projectors elevatorSecurity bar Anti-theft chain or wire Security slot FootSpeakers VCR/DVD player Connecting your devicesAbout Plug-and-Play capability Connecting your devicesAC inlet Connector of the power cord to the outlet Connecting power supplyPutting batteries Remote controlChanging the frequency of remote control signal About the remote control signalFront and top sensors Back sensorTurning on the power Power on/offTurning off the power When Auto on in the Option menu is set to Turn OFFSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundSelecting an input signal Searching an input signal For an RGB signal  For no signalUsing the automatic adjustment feature Adjusting the zoom and focus For a video signal or s-video signal  For a component video signalCorrecting the keystone distortions Adjusting the positionFreezing the screen Using the magnify featureTemporarily blanking the screen Easy Menu Using the menu functionAdvanced Menu Easy Menu Easy Menu Gamma Picture MenuPicture Menu Using the / buttons switches the color temperature modeCustom and then pressing the button or Color TempLOAD1, LOAD2, LOAD3, LOAD4 Active IrisMY Memory SAVE1, SAVE2, SAVE3, SAVE4For no signal For an RGB signalImage Menu Over ScanAuto Adjust PhaseImage Menu SizeProgressive Input Menu3D-YCS Color SpaceComponent Input MenuVideo Format Frame Lock Custom Resolution BOX ResolutionSome input, this function may not work well Setup MenuFunction may not work correctly Function may not work wellSetup Menu Audio Menu VolumeSpeaker AudioUsing the / buttons switches the mode for the blank screen Using the /// buttons adjusts the menu positionScreen Menu Or keep no operation for about 10 secondsStart UP Screen MenuMyScreen Capturing error has occurred. Please try againMyScreen registration is finished Message Auto Search Option MenuAuto on Auto OFF Option MenuLamp Time MY Button ServiceFAN Speed Filter Message GhostKEY Lock Factory ResetRemote Receiv Remote FreqInputting the Password Using Security FeaturesSecurity Description If you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Setting the PasswordTurning the Password off Using the PIN Lock FunctionRegistering the PIN Code If you have forgotten your PIN Code Turning Off the PIN Lock FunctionSetting the Transition Detector Password Using the Transition Detector FunctionTurning On the Transition Detector Function Security Setting the Transition Detector offCase of replacement by yourself MaintenanceLamp Type number = DT00771 Replacing the lampLamp Air filter Type number = MU03642 Cleaning the air filterAir filter Page There is no input signal TroubleshootingInternal temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps Power switch is not set to the on position Electrical power cord is not pluggedSignal cables are not correctly connected Signal source does not correctly workAudio setting is not correct Volume is adjusted to an extremely low levelColor settings are not correctly adjusted Color Space setting is not suitableEither the focus and/or horizontal phase settings are Not properly adjustedWhisper function is working Lamp is approaching the end of its product LifetimeSpecification Warranty and after-serviceSpecifications