Hitachi CP-X600 user manual Image Menu, For an RGB signal, For no signal, Over Scan, Position

Page 28

IMAGE Menu

IMAGE Menu

From the IMAGE menu, items shown in the table below can be performed.

Select an item using the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or remote control, or ENTER button on the remote control to execute the item. Then perform it according to the following table.

/'07=4)$?

5'.'%6

 





2+%674'

#52'%6

+/#)'

18'45%#0

+0276

8215+6+10

5'672

*215+6+10

#7&+1

*2*#5'

5%4''0

*5+<'

126+10

#761#&,756':'%76'

'#5;/'07



 

Item

Description

 

 

 

Using the ▲/▼ buttons switches the mode for aspect ratio.

 

For an RGB signal

 

NORMAL ó 4:3 ó 16:9 ó SMALL

ASPECT

For a Video signal, S-video signal or Component video signal

4:3 ó 16:9 ó 14:9 ó SMALL

 

 

For no signal

 

4:3 (fixed)

 

• The NORMAL mode keeps the original aspect ratio of the signal.

 

Using the ▲/▼ buttons adjusts the over-scan ratio.

OVER SCAN

Large (It reduces picture) ó Small (It magnifies picture)

• This item can be selected only for a video, s-video and component signal.

 

• When this adjustment is too large, certain degradation may appear

 

at the frame area of the picture. In such a case, please adjust small.

 

Using the ▲/▼ buttons adjusts the vertical position.

 

Up ó Down

 

• Over-adjusting the vertical position may cause noise to appear

 

on the screen. If this occurs please reset the vertical position to the

V POSITION

default setting. Pressing the RESET button when the V POSITION

is selected will reset the V POSITION to the default setting.

 

 

• When this function is performed on a video signal, s-video signal,

 

or component video signal of 525i (480i) or 625i (576i), the range of

 

this adjustment depends on the OVER SCAN (above) setting. It is

 

not possible to adjust when the OVER SCAN is set to 10.

 

Using the ▲/▼ buttons adjusts the horizontal position.

 

Left ó Right

 

• Over-adjusting the horizontal position may cause noise to appear

 

on the screen. If this occurs please reset the horizontal position to the

H POSITION

default setting. Pressing the RESET button when the H POSITION is

selected will reset the H POSITION to the default setting.

 

 

• When this function is performed on a video signal, s-video signal,

 

or component video signal of 525i (480i) or 625i (576i), the range of

 

this adjustment depends on the OVER SCAN (above) setting. It is

 

not possible to adjust when the OVER SCAN is set to 10.

(continued on next page)

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Thank you for purchasing this projector About this manualTrademark acknowledgment Content Contents of package Fastening the lens coverPart names ProjectorHOT!4 HOTControl panel Rear panelCB/PB, CR/PR ports 10 Audio IN4 R/L ports 10 RGB OUT port 10 Audio OUT port 10Remote control Back Remote controlSetting up Arrangement On a horizontal surfaceSuspended from the ceiling DownAdjusting the projectors elevator Using the security bar and slotSecurity bar Anti-theft chain or wire Security slot FootConnecting your devices Speakers VCR/DVD playerConnecting your devices About Plug-and-Play capabilityConnecting power supply AC inlet Connector of the power cord to the outletRemote control Putting batteriesAbout the remote control signal Changing the frequency of remote control signalFront and top sensors Back sensorPower on/off Turning on the powerTurning off the power When Auto on in the Option menu is set to Turn OFFAdjusting the volume Selecting an input signalOperating Temporarily muting the soundSearching an input signal Selecting an input signal For an RGB signal  For no signalAdjusting the zoom and focus Using the automatic adjustment feature For a video signal or s-video signal  For a component video signalAdjusting the position Correcting the keystone distortionsUsing the magnify feature Freezing the screenTemporarily blanking the screen Easy Menu Using the menu functionAdvanced Menu Easy Menu Easy Menu Picture Menu GammaUsing the / buttons switches the color temperature mode Picture MenuCustom and then pressing the button or Color TempActive Iris LOAD1, LOAD2, LOAD3, LOAD4MY Memory SAVE1, SAVE2, SAVE3, SAVE4For an RGB signal For no signalImage Menu Over ScanPhase Auto AdjustImage Menu SizeInput Menu Progressive3D-YCS Color SpaceComponent Input MenuVideo Format Frame Lock Resolution Custom Resolution BOXSetup Menu Some input, this function may not work wellFunction may not work correctly Function may not work wellSetup Menu Volume Audio MenuSpeaker AudioUsing the /// buttons adjusts the menu position Using the / buttons switches the mode for the blank screenScreen Menu Or keep no operation for about 10 secondsScreen Menu Start UPMyScreen Capturing error has occurred. Please try againMyScreen registration is finished Message Auto Search Option MenuAuto on Auto OFF Option MenuLamp Time MY Button ServiceFAN Speed Ghost Filter MessageFactory Reset KEY LockRemote Receiv Remote FreqInputting the Password Using Security FeaturesSecurity Using the MyScreen Password Function Description If you have forgotten your PasswordTurning on the MyScreen Password Setting the PasswordTurning the Password off Using the PIN Lock FunctionRegistering the PIN Code Turning Off the PIN Lock Function If you have forgotten your PIN CodeSetting the Transition Detector Password Using the Transition Detector FunctionTurning On the Transition Detector Function Setting the Transition Detector off SecurityMaintenance Case of replacement by yourselfLamp Type number = DT00771 Replacing the lampLamp Type number = MU03642 Cleaning the air filter Air filterAir filter Page Troubleshooting There is no input signalInternal temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps Electrical power cord is not plugged Power switch is not set to the on positionSignal cables are not correctly connected Signal source does not correctly workVolume is adjusted to an extremely low level Audio setting is not correctColor settings are not correctly adjusted Color Space setting is not suitableNot properly adjusted Either the focus and/or horizontal phase settings areWhisper function is working Lamp is approaching the end of its product LifetimeWarranty and after-service SpecificationSpecifications
Top Page Image Contents