Hitachi CP-X600 Electrical power cord is not plugged, Power switch is not set to the on position

Page 60

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects

WARNING ►Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer or service company.

1. Before requesting repair, please check in accordance with the following chart. This operation sometimes

resolves your problem. If the situation cannot be corrected,

2. The projector’s microprocessor may need to be reset. Please push the Shutdown switch by using a pin or

similar and the projector will be turned off immediately.

Before turning it again, wait at least 10 minutes to make the projector cool down enough.

3. Some setting may be wrong. Please use the FACTORY RESET function of the SERVICE item in the OPTION menu (45) to reset all settings to factory default.

Then, if the problem is not removed after the remedy, please contact your dealer or service company.

Phenomenon

Cases not involving a machine defect

Reference

page

 

 

 

 

 

 

The electrical power cord is not plugged in.

12

 

Correctly connect the power cord.

 

 

 

The power switch is not set to the on position.

15

 

Set the power switch to [ ] (On).

 

 

 

The main power source has been interrupted during

 

Power does not

operation such as by a power outage (blackout), etc.

15

Please turn the power off, and allow the projector to cool

come on.

down at least 2 minutes, then turn the power on again.

 

 

 

 

Either there is no lamp and/or lamp cover, or either

 

 

of these has not been properly fixed.

 

 

Please turn the power off, and allow the projector to cool down

52

 

at least 45 minutes. After the projector has sufficiently cooled

 

 

 

down, please make confirmation of the attachment state of the

 

 

lamp and lamp cover, and then turn the power on again.

 

 

The signal cables are not correctly connected.

10

 

Correctly connect the connection cables.

 

 

Neither sounds

Signal source does not correctly work.

 

nor pictures are

Correctly set up the signal source device by referring to the

–

outputted.

manual of the source device.

 

 

The input changeover settings are mismatched.

17, 18

 

Select the input signal, and correct the settings.

 

 

60

Page 59 Page 61
Image 60
Page 59 Page 61
Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Content Contents of package Fastening the lens coverPart names ProjectorHOT!4 HOTControl panel Rear panelCB/PB, CR/PR ports 10 Audio IN4 R/L ports 10 RGB OUT port 10 Audio OUT port 10Remote control Back Remote controlSetting up Arrangement On a horizontal surfaceSuspended from the ceiling DownAdjusting the projectors elevator Using the security bar and slotSecurity bar Anti-theft chain or wire Security slot FootConnecting your devices Speakers VCR/DVD playerConnecting your devices About Plug-and-Play capabilityConnecting power supply AC inlet Connector of the power cord to the outletRemote control Putting batteriesAbout the remote control signal Changing the frequency of remote control signalFront and top sensors Back sensorPower on/off Turning on the powerTurning off the power When Auto on in the Option menu is set to Turn OFFAdjusting the volume Selecting an input signalOperating Temporarily muting the soundSearching an input signal Selecting an input signal For an RGB signal  For no signalAdjusting the zoom and focus Using the automatic adjustment feature For a video signal or s-video signal  For a component video signalAdjusting the position Correcting the keystone distortionsUsing the magnify feature Freezing the screenTemporarily blanking the screen Using the menu function Easy MenuAdvanced Menu Easy Menu Easy Menu Picture Menu GammaUsing the / buttons switches the color temperature mode Picture MenuCustom and then pressing the button or Color TempActive Iris LOAD1, LOAD2, LOAD3, LOAD4MY Memory SAVE1, SAVE2, SAVE3, SAVE4For an RGB signal For no signalImage Menu Over ScanPhase Auto AdjustImage Menu SizeInput Menu Progressive3D-YCS Color SpaceInput Menu ComponentVideo Format Frame Lock Resolution Custom Resolution BOXSetup Menu Some input, this function may not work wellFunction may not work correctly Function may not work wellSetup Menu Volume Audio MenuSpeaker AudioUsing the /// buttons adjusts the menu position Using the / buttons switches the mode for the blank screenScreen Menu Or keep no operation for about 10 secondsScreen Menu Start UPCapturing error has occurred. Please try again MyScreenMyScreen registration is finished Message Option Menu Auto SearchAuto on Option Menu Auto OFFLamp Time Service MY ButtonFAN Speed Ghost Filter MessageFactory Reset KEY LockRemote Receiv Remote FreqUsing Security Features Inputting the PasswordSecurity Using the MyScreen Password Function Description If you have forgotten your PasswordTurning on the MyScreen Password Setting the PasswordUsing the PIN Lock Function Turning the Password offRegistering the PIN Code Turning Off the PIN Lock Function If you have forgotten your PIN CodeUsing the Transition Detector Function Setting the Transition Detector PasswordTurning On the Transition Detector Function Setting the Transition Detector off SecurityMaintenance Case of replacement by yourselfLamp Type number = DT00771 Replacing the lampLamp Type number = MU03642 Cleaning the air filter Air filterAir filter Page Troubleshooting There is no input signalInternal temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps Electrical power cord is not plugged Power switch is not set to the on positionSignal cables are not correctly connected Signal source does not correctly workVolume is adjusted to an extremely low level Audio setting is not correctColor settings are not correctly adjusted Color Space setting is not suitableNot properly adjusted Either the focus and/or horizontal phase settings areWhisper function is working Lamp is approaching the end of its product LifetimeWarranty and after-service SpecificationSpecifications
Top Page Image Contents