Hitachi CP-X600 user manual Troubleshooting, Related messages, There is no input signal

Page 57

Troubleshooting

Troubleshooting

Related messages

When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please follow the instructions described below. If the same message is displayed after the remedy, or if a message other than the following appears, please contact your dealer or service company.

Although these messages will be automatically disappeared around several minutes, it will be reappeared every time the power is turned on.

Message

Description

	NO INPUT IS DETECTED	There is no input signal.
	NO INPUT IS DETECTED	Please confirm the signal input connection, and the status
		Please confirm the signal input connection, and the status
		of the signal source.

	SYNC IS OUT OF RANGE	The horizontal or vertical frequency of the input signal
	SYNC IS OUT OF RANGE	is not within the specified range.
		is not within the specified range.
	fH kHz fV Hz	Please confirm the specs for your projector or the signal
		source specs.
		The internal temperature is rising.
		Please turn the power off, and allow the projector to cool
		down at least 20 minutes. After having confirmed the
		following items, please turn the power ON again.
	CHECK THE AIR FLOW	• Is there blockage of the air passage aperture?
		• Is the air filter dirty?
		• Does the peripheral temperature exceed 35°C?
		If the same indication is displayed after the remedy, please set
		FAN SPEED of the SERVICE item in the OPTION menu to HIGH.
	REMINDER	A note of precaution when cleaning the air filter.

***HRS PASSED AFTER THE Please immediately turn the power off, and clean or change

LAST FILTER CHECK.	the air filter referring to the “Air Filter” section of this manual
FILTER MAINTENANCE IS ESSENTIAL (54). After you have cleaned or changed the air filter,
TO REMOVE WARNING MESSAGE, please be sure to reset the filter timer (24, 42).
RESET FILTER TIMER.
SEE MANUAL FURTHER INFO.

57

Image 57

Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Content Fastening the lens cover Contents of packageProjector Part namesHOT!4 HOTRear panel Control panelCB/PB, CR/PR ports 10 Audio IN4 R/L ports 10 RGB OUT port 10 Audio OUT port 10Back Remote control Remote controlSetting up On a horizontal surface ArrangementSuspended from the ceiling DownUsing the security bar and slot Adjusting the projectors elevatorSecurity bar Anti-theft chain or wire Security slot FootSpeakers VCR/DVD player Connecting your devicesAbout Plug-and-Play capability Connecting your devicesAC inlet Connector of the power cord to the outlet Connecting power supplyPutting batteries Remote controlChanging the frequency of remote control signal About the remote control signalFront and top sensors Back sensorTurning on the power Power on/offTurning off the power When Auto on in the Option menu is set to Turn OFFSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundSelecting an input signal Searching an input signal For an RGB signal  For no signalUsing the automatic adjustment feature Adjusting the zoom and focus For a video signal or s-video signal  For a component video signalCorrecting the keystone distortions Adjusting the positionFreezing the screen Using the magnify featureTemporarily blanking the screen Using the menu function Easy MenuAdvanced Menu Easy Menu Easy Menu Gamma Picture MenuPicture Menu Using the / buttons switches the color temperature modeCustom and then pressing the button or Color TempLOAD1, LOAD2, LOAD3, LOAD4 Active IrisMY Memory SAVE1, SAVE2, SAVE3, SAVE4For no signal For an RGB signalImage Menu Over ScanAuto Adjust PhaseImage Menu SizeProgressive Input Menu3D-YCS Color SpaceInput Menu ComponentVideo Format Frame Lock Custom Resolution BOX ResolutionSome input, this function may not work well Setup MenuFunction may not work correctly Function may not work wellSetup Menu Audio Menu VolumeSpeaker AudioUsing the / buttons switches the mode for the blank screen Using the /// buttons adjusts the menu positionScreen Menu Or keep no operation for about 10 secondsStart UP Screen MenuCapturing error has occurred. Please try again MyScreenMyScreen registration is finished Message Option Menu Auto SearchAuto on Option Menu Auto OFFLamp Time Service MY ButtonFAN Speed Filter Message GhostKEY Lock Factory ResetRemote Receiv Remote FreqUsing Security Features Inputting the PasswordSecurity Description If you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Setting the PasswordUsing the PIN Lock Function Turning the Password offRegistering the PIN Code If you have forgotten your PIN Code Turning Off the PIN Lock FunctionUsing the Transition Detector Function Setting the Transition Detector PasswordTurning On the Transition Detector Function Security Setting the Transition Detector offCase of replacement by yourself MaintenanceLamp Type number = DT00771 Replacing the lampLamp Air filter Type number = MU03642 Cleaning the air filterAir filter Page There is no input signal TroubleshootingInternal temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps Power switch is not set to the on position Electrical power cord is not pluggedSignal cables are not correctly connected Signal source does not correctly workAudio setting is not correct Volume is adjusted to an extremely low levelColor settings are not correctly adjusted Color Space setting is not suitableEither the focus and/or horizontal phase settings are Not properly adjustedWhisper function is working Lamp is approaching the end of its product LifetimeSpecification Warranty and after-serviceSpecifications